Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 35.1
edited by ahenkel
on 2021-12-12 22:09
Change comment: There is no comment for this version
To version 30.1
edited by ahenkel
on 2021-12-07 17:44
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -79,7 +79,7 @@
79 79  
80 80  Be aware to which channel and nozzle line your sample is connected.
81 81  
82 - Red → Channel 1, crystal line (nozzle capillary without marks/with red marks)
82 + Red → Channel 1, crystal line (nozzle capillary without marks)
83 83  
84 84   Green → Channel 2, substrate line (nozzle capillary is marked in black)
85 85  
... ... @@ -166,16 +166,14 @@
166 166  
167 167  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Temperaturecontrol/Chiller"/}}**Temperature control/Chiller** ====
168 168  
169 -* The chiller circulates fluid through the gas nozzle.
169 +* The chiller circulates fluid through the gas\\
170 170  
171 171  \\
172 172  
173 -==== {{id name="14.SerialCrystallography:CFELTapeDrive-Gasnozzle"/}}**Gas nozzle** ====
173 +\\
174 174  
175 175  \\
176 176  
177 -==== {{id name="14.SerialCrystallography:CFELTapeDrive-IRcamera"/}}**IR camera** ====
178 -
179 179  \\
180 180  
181 181  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
... ... @@ -195,14 +195,13 @@
195 195  * Remove the (almost) empty feeder roll by pulling it upwards.
196 196  * Cut the tape with some cm overlap to glue to the new roll. **Do not discard empty roll!**
197 197  * Get a new tape roll (bottom left on the cart). **Polypropylen 15 µm**
198 -* Cut the first cm of the new tape roll, directly behind the black sticky part.
199 -* Place new roll on roll holder and use sticky tape to attach the end of the old tape to the beginning of the new roll.
200 -* Open magnetic tape stabilizer on the **left side**. //!!!BEAMSTOP!!!//
201 -* Start the tape (3mm/s). Once the connetion side has arrived at the collector roll, stop the tape (0mm/s).
202 -* Again, cut the tape directly behind the connection side. Replace the the old roll with the **empty **one. Old roll can be discarded.
203 -* Attach new tape to the empty roll by using some sticky tape.
196 +* Cut the first cm of the new tape roll, directly before the black sticky part.
197 +* Use this sticky part to attach the end of the old tape to the new roll. Place new roll on roll holder.
198 +* Open magnetic tape stabilizer.
199 +* Start the tape (3mm/s). Once the connetion side (black sticky part) has arrived at the collector roll, stop the tape (0mm/s).
200 +* Again, cut the tape directly in front of the black mark. Replace the the old roll with the **empty **one. Old roll can be discarded.
201 +* Attach new tape to the empty roll by using the black sticky part.
204 204  * Close tape stabilizer.
205 -* Reset tape counter in kamzik by clicking "<Call>" in "Main-Tape".
206 206  
207 207  **[[image:attach:20211201_094101.jpg||height="250"]][[image:attach:20211201_094111.jpg||height="250"]]
208 208  **
Confluence.Code.ConfluencePageClass[0]
Id
... ... @@ -1,1 +1,1 @@
1 -236824561
1 +236815972
URL
... ... @@ -1,1 +1,1 @@
1 -https://confluence.desy.de/spaces/11/pages/236824561/14. Serial Crystallography: CFEL TapeDrive
1 +https://confluence.desy.de/spaces/11/pages/236815972/14. Serial Crystallography: CFEL TapeDrive