Changes for page CFEL TapeDrive: Serial Crystallography

Last modified by chatzies on 2025-11-27 11:35

From 35.1 to 36.1 From 42.1 to 43.1

From version 36.1

edited by ahenkel
on 2021-12-12 22:53

Change comment: There is no comment for this version

To version 42.1

edited by ahenkel
on 2021-12-12 23:47

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Objects (1 modified, 0 added, 0 removed)
- Confluence.Code.ConfluencePageClass[0]

Details

Page properties

Content

@@ -1,3 +1,6 @@
++{{layout}}
++{{layout-section ac:type="single"}}
++{{layout-cell}}
  {{toc/}}
@@ -215,21 +215,76 @@
  === {{id name="14.SerialCrystallography:CFELTapeDrive-14.6Nozzleexchange"/}}**14.6 Nozzle exchange** ===
--\\
++=== {{id name="14.SerialCrystallography:CFELTapeDrive-14.7Chopper"/}}**14.7 Chopper** ===
--=== {{id name="14.SerialCrystallography:CFELTapeDrive-14.7Datacollection"/}}**14.7 Data collection** ===
++start chopper gui from terminal:
++(% class="code" %)
++(((
++            cd /gpfs/local/shared/ChopperControl
++)))
++
++(% class="code" %)
++(((
++            python chopperControl.py
++)))
++
++----
++{{/layout-cell}}
++{{/layout-section}}
++
++{{layout-section ac:type="two_equal"}}
++{{layout-cell}}
++                     [[image:attach:20211212_233140.jpg||height="250"]]
++{{/layout-cell}}
++
++{{layout-cell}}
++**Chopper → no Chopper**
++
++* decrease frequency by max. 10 Hz steps\\
++** click arrow down 10x, "Set", arrow down 10x, "Set", ....
++* at frequency = 10 Hz, click "Stop"
++* set "Hole" to <none> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
++
++(% style="color: rgb(0,0,0);" %)**no Chopper → Chopper**
++
++* (% style="color: rgb(0,0,0);" %)set "Hole" to <Inner hole (largest)> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
++* (% style="color: rgb(0,0,0);" %)increase frequency by max. 10 Hz steps
++** (% style="color: rgb(0,0,0);" %)click arrow up 10x, "Set", arrow up 10x, "Set", .....
++* (% style="color: rgb(0,0,0);" %)//usually 133 Hz, results in exposure time of 3.7 ms//
++{{/layout-cell}}
++{{/layout-section}}
++
++{{layout-section ac:type="single"}}
++{{layout-cell}}
++=== {{id name="14.SerialCrystallography:CFELTapeDrive-14.8Datacollection"/}}**14.8 Data collection** ===
++
  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
--                                        xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
--                                        password: //written on control laptop (changes every 6 months)//
++(% class="code" %)
++(((
++                      xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
++                      password: written on control laptop (changes every 6 months)
++)))
                                             //>>usually the terminal is open, just repeat previous command with arrow up, enter and type in the password//
  \\
++Click "Start" icon in kamzik.
++
++[[image:attach:kamzik_run-tile.jpg||height="400"]]
++
++----
++{{/layout-cell}}
++{{/layout-section}}
++
++{{layout-section ac:type="two_equal"}}
++{{layout-cell}}
  **Check list:**
++(% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
++
  * Open BS1  (//CrystalControl)//
  * Put collimator in (//CrystalControl)//
  * Check beamstop position = 27 000 (//Atk panel p11/motor/eh.3.09)//
@@ -239,13 +239,33 @@
  \\
--**Start run in kamzik
--**
++**Set run parameters and go 🏃💥**
--Click "Start" icon in kamzik.
++1. Set your desired No. of frames
++1. Match exposure time with chopper setting
++1. Check trigger setting and match to chopper setting
++1. Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
++1. To start the run, click "<Call>" next to //exposure time//
--[[image:attach:kamzik_run-tile.jpg||height="400"]]
++\\
++(% style="color: rgb(153,51,102);" %)**//Current bug~://**
++
++(% style="color: rgb(0,0,0);" %)You need to "Stop" run in kamzik manually after all images have been acquired. This moves the shield up and closes the fast shutter. Afterwards you can start a new run by clicking "<Call>".
++
++
++(% style="color: rgb(0,0,0);" %)Check progress in terminal with:
++
++(% class="code" %)
++(((
++      cd /gpfs/current/raw/scan_frames
++      watch "ls -lrt <run number>/ | tail"
++\\\\\\\\
++)))
++{{/layout-cell}}
++
++{{layout-cell}}
++(% class="wrapped relative-table" style="width: 100.0%;" %)
  |=(((
  Parameter
  )))|=(((
@@ -303,52 +303,45 @@
  )))|(% colspan="1" %)(((
  read out of diode
  )))|(% colspan="1" %)(((
--**~~ 0   !!! higher values indicate missaligned beam stop!!!**
++**~~ 0   !!! higher values indicate missaligned beam stop!!!
++Call local contact
++**
  )))
++{{/layout-cell}}
++{{/layout-section}}
++{{layout-section ac:type="single"}}
++{{layout-cell}}
  ----
--(% class="task-list" %)
--(((
--{{task reference="/Tasks/Task_6" status="InProgress"}}
--Set your desired No. of frames
--{{/task}}
++=== {{id name="14.SerialCrystallography:CFELTapeDrive-14.9Troubleshooting"/}}14.9 Troubleshooting ===
--{{task reference="/Tasks/Task_7" status="InProgress"}}
--Match exposure time with chopper setting
--{{/task}}
++* (((
++==== {{id name="14.SerialCrystallography:CFELTapeDrive-Tapestopped"/}}Tape stopped ====
--{{task reference="/Tasks/Task_8" status="InProgress"}}
--Check trigger setting and match to chopper setting
--{{/task}}
--
--{{task reference="/Tasks/Task_9" status="InProgress"}}
--Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
--{{/task}}
--
--{{task reference="/Tasks/Task_10" status="InProgress"}}
--To start the run, click "<Call>" next to //exposure time//
--{{/task}}
++* Tape roll empty?
++* motor connected (icon green)?
  )))
------
--
  \\
--\\
--
--=== {{id name="14.SerialCrystallography:CFELTapeDrive-14.8Troubleshooting"/}}14.8 Troubleshooting ===
--
  * (((
--==== {{id name="14.SerialCrystallography:CFELTapeDrive-Tapestopped"/}}Tape stopped ====
--)))
--* (((
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Nozzlemotorsarenotresponding"/}}Nozzle motors are not responding ====
++
++* displayed in green=connected?
++* nozzle holder colliding somewhere?
++* motor limits reached? → position displayed in red
  )))
--* (((
--==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
--)))
  \\
--\\
++* (((
++==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
++
++* channel turned on?
++* Sample empty?
++* Nozzle or lines clogged? → flush with water, change nozzle
++)))
++{{/layout-cell}}
++{{/layout-section}}
++{{/layout}}

Confluence.Code.ConfluencePageClass[0]

Id

@@ -1,1 +1,1 @@
--236824562
++236824589

URL

@@ -1,1 +1,1 @@
--https://confluence.desy.de/spaces/11/pages/236824562/14. Serial Crystallography: CFEL TapeDrive
++https://confluence.desy.de/spaces/11/pages/236824589/14. Serial Crystallography: CFEL TapeDrive

Changes for page CFEL TapeDrive: Serial Crystallography

Summary

Details

Applications

Navigation