Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 39.1
edited by ahenkel
on 2021-12-12 23:00
Change comment: There is no comment for this version
To version 41.1
edited by ahenkel
on 2021-12-12 23:20
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -224,27 +224,16 @@
224 224  
225 225  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
226 226  
227 - xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
228 - password: //written on control laptop (changes every 6 months)//
227 +(% class="code" %)
228 +(((
229 + xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
230 + password: written on control laptop (changes every 6 months)
231 +)))
229 229  
230 230   //>>usually the terminal is open, just repeat previous command with arrow up, enter and type in the password//
231 231  
232 232  \\
233 233  
234 -**Check list:**
235 -
236 -* Open BS1  (//CrystalControl)//
237 -* Put collimator in (//CrystalControl)//
238 -* Check beamstop position = 27 000 (//Atk panel p11/motor/eh.3.09)//
239 -* Open fast shutter (//CrystalControl)//
240 -* Check diode voltage ~~ 0.0 (//kamzik Run/Diode voltage)//
241 -* Close fast shutter (//CrystalControl)//
242 -
243 -\\
244 -
245 -**Start run in kamzik
246 -**
247 -
248 248  Click "Start" icon in kamzik.
249 249  
250 250  [[image:attach:kamzik_run-tile.jpg||height="400"]]
... ... @@ -255,17 +255,46 @@
255 255  
256 256  {{layout-section ac:type="two_equal"}}
257 257  {{layout-cell}}
247 +**Check list:**
248 +
249 +(% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
250 +
251 +* Open BS1  (//CrystalControl)//
252 +* Put collimator in (//CrystalControl)//
253 +* Check beamstop position = 27 000 (//Atk panel p11/motor/eh.3.09)//
254 +* Open fast shutter (//CrystalControl)//
255 +* Check diode voltage ~~ 0.0 (//kamzik Run/Diode voltage)//
256 +* Close fast shutter (//CrystalControl)//
257 +
258 258  \\
259 259  
260 +**Set run parameters and go 🏃💥**
261 +
260 260  1. Set your desired No. of frames
261 261  1. Match exposure time with chopper setting
262 262  1. Check trigger setting and match to chopper setting
263 263  1. Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
264 264  1. To start the run, click "<Call>" next to //exposure time//
267 +
268 +\\
269 +
270 +(% style="color: rgb(153,51,102);" %)**//Current bug~://**
271 +
272 +(% style="color: rgb(0,0,0);" %)You need to "Stop" run in kamzik manually after all images have been acquired. This moves the shield up and closes the fast shutter. Afterwards you can start a new run by clicking "<Call>".
273 +
274 +
275 +(% style="color: rgb(0,0,0);" %)Check progress in terminal with:
276 +
277 +(% class="code" %)
278 +(((
279 + cd /gpfs/current/raw/scan_frames
280 + watch "ls -lrt <run number>/ | tail"
281 +\\\\\\\\
282 +)))
265 265  {{/layout-cell}}
266 266  
267 267  {{layout-cell}}
268 -(% class="wrapped" %)
286 +(% class="wrapped relative-table" style="width: 100.0%;" %)
269 269  |=(((
270 270  Parameter
271 271  )))|=(((
... ... @@ -323,7 +323,9 @@
323 323  )))|(% colspan="1" %)(((
324 324  read out of diode
325 325  )))|(% colspan="1" %)(((
326 -**~~ 0 !!! higher values indicate missaligned beam stop!!!**
344 +**~~ 0 !!! higher values indicate missaligned beam stop!!! 
345 +Call local contact
346 +**
327 327  )))
328 328  {{/layout-cell}}
329 329  {{/layout-section}}
... ... @@ -330,16 +330,35 @@
330 330  
331 331  {{layout-section ac:type="single"}}
332 332  {{layout-cell}}
353 +----
354 +
333 333  === {{id name="14.SerialCrystallography:CFELTapeDrive-14.8Troubleshooting"/}}14.8 Troubleshooting ===
334 334  
335 335  * (((
336 336  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Tapestopped"/}}Tape stopped ====
359 +
360 +* Tape roll empty?
361 +* motor connected (icon green)?
337 337  )))
363 +
364 +\\
365 +
338 338  * (((
339 339  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Nozzlemotorsarenotresponding"/}}Nozzle motors are not responding ====
368 +
369 +* displayed in green=connected?
370 +* nozzle holder colliding somewhere?
371 +* motor limits reached? → position displayed in red
340 340  )))
373 +
374 +\\
375 +
341 341  * (((
342 342  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
378 +
379 +* channel turned on?
380 +* Sample empty?
381 +* Nozzle or lines clogged? → flush with water, change nozzle
343 343  )))
344 344  {{/layout-cell}}
345 345  {{/layout-section}}
Confluence.Code.ConfluencePageClass[0]
Id
... ... @@ -1,1 +1,1 @@
1 -236824573
1 +236824588
URL
... ... @@ -1,1 +1,1 @@
1 -https://confluence.desy.de/spaces/11/pages/236824573/14. Serial Crystallography: CFEL TapeDrive
1 +https://confluence.desy.de/spaces/11/pages/236824588/14. Serial Crystallography: CFEL TapeDrive