Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 41.1
edited by ahenkel
on 2021-12-12 23:20
Change comment: There is no comment for this version
To version 39.1
edited by ahenkel
on 2021-12-12 23:00
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -224,30 +224,15 @@
224 224  
225 225  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
226 226  
227 -(% class="code" %)
228 -(((
229 - xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
230 - password: written on control laptop (changes every 6 months)
231 -)))
227 + xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
228 + password: //written on control laptop (changes every 6 months)//
232 232  
233 233   //>>usually the terminal is open, just repeat previous command with arrow up, enter and type in the password//
234 234  
235 235  \\
236 236  
237 -Click "Start" icon in kamzik.
238 -
239 -[[image:attach:kamzik_run-tile.jpg||height="400"]]
240 -
241 -----
242 -{{/layout-cell}}
243 -{{/layout-section}}
244 -
245 -{{layout-section ac:type="two_equal"}}
246 -{{layout-cell}}
247 247  **Check list:**
248 248  
249 -(% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
250 -
251 251  * Open BS1  (//CrystalControl)//
252 252  * Put collimator in (//CrystalControl)//
253 253  * Check beamstop position = 27 000 (//Atk panel p11/motor/eh.3.09)//
... ... @@ -257,33 +257,30 @@
257 257  
258 258  \\
259 259  
260 -**Set run parameters and go 🏃💥**
245 +**Start run in kamzik
246 +**
261 261  
248 +Click "Start" icon in kamzik.
249 +
250 +[[image:attach:kamzik_run-tile.jpg||height="400"]]
251 +
252 +----
253 +{{/layout-cell}}
254 +{{/layout-section}}
255 +
256 +{{layout-section ac:type="two_equal"}}
257 +{{layout-cell}}
258 +\\
259 +
262 262  1. Set your desired No. of frames
263 263  1. Match exposure time with chopper setting
264 264  1. Check trigger setting and match to chopper setting
265 265  1. Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
266 266  1. To start the run, click "<Call>" next to //exposure time//
267 -
268 -\\
269 -
270 -(% style="color: rgb(153,51,102);" %)**//Current bug~://**
271 -
272 -(% style="color: rgb(0,0,0);" %)You need to "Stop" run in kamzik manually after all images have been acquired. This moves the shield up and closes the fast shutter. Afterwards you can start a new run by clicking "<Call>".
273 -
274 -
275 -(% style="color: rgb(0,0,0);" %)Check progress in terminal with:
276 -
277 -(% class="code" %)
278 -(((
279 - cd /gpfs/current/raw/scan_frames
280 - watch "ls -lrt <run number>/ | tail"
281 -\\\\\\\\
282 -)))
283 283  {{/layout-cell}}
284 284  
285 285  {{layout-cell}}
286 -(% class="wrapped relative-table" style="width: 100.0%;" %)
268 +(% class="wrapped" %)
287 287  |=(((
288 288  Parameter
289 289  )))|=(((
... ... @@ -341,9 +341,7 @@
341 341  )))|(% colspan="1" %)(((
342 342  read out of diode
343 343  )))|(% colspan="1" %)(((
344 -**~~ 0 !!! higher values indicate missaligned beam stop!!! 
345 -Call local contact
346 -**
326 +**~~ 0 !!! higher values indicate missaligned beam stop!!!**
347 347  )))
348 348  {{/layout-cell}}
349 349  {{/layout-section}}
... ... @@ -350,35 +350,16 @@
350 350  
351 351  {{layout-section ac:type="single"}}
352 352  {{layout-cell}}
353 -----
354 -
355 355  === {{id name="14.SerialCrystallography:CFELTapeDrive-14.8Troubleshooting"/}}14.8 Troubleshooting ===
356 356  
357 357  * (((
358 358  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Tapestopped"/}}Tape stopped ====
359 -
360 -* Tape roll empty?
361 -* motor connected (icon green)?
362 362  )))
363 -
364 -\\
365 -
366 366  * (((
367 367  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Nozzlemotorsarenotresponding"/}}Nozzle motors are not responding ====
368 -
369 -* displayed in green=connected?
370 -* nozzle holder colliding somewhere?
371 -* motor limits reached? → position displayed in red
372 372  )))
373 -
374 -\\
375 -
376 376  * (((
377 377  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
378 -
379 -* channel turned on?
380 -* Sample empty?
381 -* Nozzle or lines clogged? → flush with water, change nozzle
382 382  )))
383 383  {{/layout-cell}}
384 384  {{/layout-section}}
Confluence.Code.ConfluencePageClass[0]
Id
... ... @@ -1,1 +1,1 @@
1 -236824588
1 +236824573
URL
... ... @@ -1,1 +1,1 @@
1 -https://confluence.desy.de/spaces/11/pages/236824588/14. Serial Crystallography: CFEL TapeDrive
1 +https://confluence.desy.de/spaces/11/pages/236824573/14. Serial Crystallography: CFEL TapeDrive