Changes for page CFEL TapeDrive: Serial Crystallography

Last modified by chatzies on 2025-11-27 11:35

From 55.1 to 54.1 From 68.1 to 67.1

From version 67.1

edited by ahenkel
on 2022-05-07 18:33

Change comment: There is no comment for this version

To version 55.1

edited by ahenkel
on 2022-04-04 19:58

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)
Objects (1 modified, 0 added, 0 removed)
- Confluence.Code.ConfluencePageClass[0]

Details

Page properties

Content

@@ -17,7 +17,7 @@
  Preparation:
--* filter through 30 µm cell filter (green) or 50 µm (yellow)   into Eppendorf or Falcon (original!) tube
++* filter through 30 µm cell filter (green) into Eppendorf or Falcon (original!) tube
  [[image:attach:20211201_095534.jpg||height="250"]]
@@ -57,7 +57,7 @@
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Tape"/}}**Tape** ====
--* Click the 'main tape' icon
++* Click on the 'main tape' icon
  * Change the velocity by typing anything from **0.3-3.0 mm/s**
  * Common velocity is 1.0-1.5 mm/s
  * kamzik displays the used tape in m and %. At 98% the tape will automatically stop since the rolls need to be exchanged at this point.
@@ -66,7 +66,7 @@
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Samplenozzle"/}}**Sample nozzle** ====
--* Click on the 'nozzle' icon.
++* Click an the 'nozzle' icon.
  * (((
  The nozzle position can be adjusted in xyz by clicking on the arrows up and down. (Double arrow = 10 steps). Step size can be varied, 1mm steps are rather big and should be used carefully.
  The absolute position is **not calibrated** and therefore changes after each restart of kamzik.
@@ -156,7 +156,7 @@
  * Get a new tape roll (bottom left on the cart). **Polypropylen 15 µm**
  * Cut the first cm of the new tape roll, directly behind the black sticky part.
  * Place new roll on roll holder and use sticky tape to attach the end of the old tape to the beginning of the new roll.
--* Open magnetic tape stabilizer on the **left side**. (% style="color: rgb(255,0,0);" %)//!!!BEAMSTOP!!!//
++* Open magnetic tape stabilizer on the **left side**. //!!!BEAMSTOP!!!//
  * Start the tape (3mm/s). Once the connetion side has arrived at the collector roll, stop the tape (0mm/s).
  * Again, cut the tape directly behind the connection side. Replace the the old roll with the **empty **one. Old roll can be discarded.
  * Attach new tape to the empty roll by using some sticky tape.
@@ -214,12 +214,11 @@
  * (% style="color: rgb(0,0,0);" %)set "Hole" to <Inner hole (largest)> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
  * (% style="color: rgb(0,0,0);" %)increase frequency by max. 10 Hz steps
  ** (% style="color: rgb(0,0,0);" %)click arrow up 10x, "Set", arrow up 10x, "Set", .....
--* (% style="color: rgb(0,0,0);" %)//usually 133 Hz, results in exposure time of 3.7 ms (technical exposure will always be 7.7 ms, since max. frame rate is 133 Hz
--//
++* (% style="color: rgb(0,0,0);" %)//usually 133 Hz, results in exposure time of 3.7 ms//
  {{/layout-cell}}
  {{/layout-section}}
--{{layout-section ac:type="single"}}
++{{layout-section ac:type="two_equal"}}
  {{layout-cell}}
  == {{id name="14.SerialCrystallography:CFELTapeDrive-14.6Datacollection"/}}**14.6 Data collection** ==
@@ -234,25 +234,19 @@
                                 //>>usually the terminal is open, just repeat previous command with arrow up, enter and type in the password//
  \\
--{{/layout-cell}}
--{{/layout-section}}
--{{layout-section ac:type="two_left_sidebar"}}
--{{layout-cell}}
  **Check list:**
  (% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
--(% style="color: rgb(0,0,0);" %)Click "Run" icon in kamzik.
++(% style="color: rgb(0,0,0);" %)Click "Safety" icon in kamzik.
  * Put collimator in
--** Put detector distance 200 in //prepare_for_measurement (      )
--//
--** Click "<Call>" next to //prepare_for_measurement//
++** Click "<Call>" next to //collimator_in//
  \\
--* Open beam shutter BS1 in //CrystalControl //or// P11 XRayFeed //
++* Open beam shutter BS1 in //CrystalControl//
  {{/layout-cell}}
  {{layout-cell}}
@@ -264,6 +264,8 @@
  {{layout-cell}}
  ----
++Click "Start/Run" icon in kamzik.
++
  [[image:attach:kamzik_run-tile.jpg||height="400"]]
  ----
@@ -275,10 +275,10 @@
  **Set run parameters and go 🏃💥**
 . Set your desired No. of frames
--1. Match exposure time with chopper setting or set desired exposure time
++1. Match exposure time with chopper setting
 . Check trigger setting and match to chopper setting
--1. To start the run, click "<Call>" next to //start_run (exposure    )
--//
++1. Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
++1. To start the run, click "<Call>" next to //exposure time//
  \\
@@ -320,7 +320,7 @@
  \\
  )))|(% colspan="1" %)(((
--chopper at 133 Hz → 7.7 ms (opening time will be 3.7)
++chopper at 133 Hz → 3.7 ms
  chopper at 66 Hz   → 7.7 ms
@@ -349,6 +349,15 @@
  )))|(% colspan="1" %)(((
 .0 mm   (% style="color: rgb(255,0,0);" %)confirm with //enter//, click "<Call>"
  )))
++|(% colspan="1" %)(((
++Diode voltage
++)))|(% colspan="1" %)(((
++read out of diode
++)))|(% colspan="1" %)(((
++**~~ 0   !!! higher values indicate missaligned beam stop!!!
++Call local contact
++**
++)))
  {{/layout-cell}}
  {{/layout-section}}

Confluence.Code.ConfluencePageClass[0]

Id

@@ -1,1 +1,1 @@
--254729368
++250178644

URL

@@ -1,1 +1,1 @@
--https://confluence.desy.de/spaces/11/pages/254729368/14. Serial Crystallography: CFEL TapeDrive
++https://confluence.desy.de/spaces/11/pages/250178644/14. Serial Crystallography: CFEL TapeDrive

Changes for page CFEL TapeDrive: Serial Crystallography

Summary

Details

Applications

Navigation