Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 74.1
edited by ahenkel
on 2022-05-07 19:08
Change comment: There is no comment for this version
To version 64.1
edited by ahenkel
on 2022-04-19 14:21
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -214,15 +214,12 @@
214 214  * (% style="color: rgb(0,0,0);" %)set "Hole" to <Inner hole (largest)> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
215 215  * (% style="color: rgb(0,0,0);" %)increase frequency by max. 10 Hz steps
216 216  ** (% style="color: rgb(0,0,0);" %)click arrow up 10x, "Set", arrow up 10x, "Set", .....
217 -* (% style="color: rgb(0,0,0);" %)//usually 133 Hz, results in exposure time of 3.7 ms (technical exposure will always be 7.7 ms, since max. frame rate is 133 Hz
218 -//
217 +* (% style="color: rgb(0,0,0);" %)//usually 133 Hz, results in exposure time of 3.7 ms//
219 219  {{/layout-cell}}
220 220  {{/layout-section}}
221 221  
222 222  {{layout-section ac:type="single"}}
223 223  {{layout-cell}}
224 -----
225 -
226 226  == {{id name="14.SerialCrystallography:CFELTapeDrive-14.6Datacollection"/}}**14.6 Data collection** ==
227 227  
228 228  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
... ... @@ -245,38 +245,60 @@
245 245  
246 246  (% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
247 247  
248 -(% style="color: rgb(0,0,0);" %)Click "Run" icon in kamzik.
245 +(% style="color: rgb(0,0,0);" %)Click "Safety" icon in kamzik.
249 249  
250 250  * Put collimator in
251 -** Put detector distance 200 in //prepare_for_measurement (      )
252 -//
253 -** Click "<Call>" next to //prepare_for_measurement//
248 +** Click "<Call>" next to //collimator_in//
254 254  
255 255  \\
256 256  
257 257  * Open beam shutter BS1 in //CrystalControl //or// P11 XRayFeed //
253 +{{/layout-cell}}
258 258  
259 -\\
255 +{{layout-cell}}
256 +[[image:attach:kamzik_safety.PNG||height="400"]]
257 +{{/layout-cell}}
258 +{{/layout-section}}
260 260  
261 -//**Set run parameters and go 🏃💥**//
260 +{{layout-section ac:type="single"}}
261 +{{layout-cell}}
262 +----
262 262  
263 -1. Set your desired No. of frames
264 -1. Match exposure time with chopper setting or set desired exposure time
265 -1. Check trigger setting and match to chopper setting
266 -no chopper → external triffer //off
267 -// chopper → external trigger// on
268 -//
269 -1. To start the run, click "<Call>" next to //start_run (exposure    )//
264 +Click "Start/Run" icon in kamzik.
265 +
266 +[[image:attach:kamzik_run-tile.jpg||height="400"]]
267 +
268 +----
270 270  {{/layout-cell}}
270 +{{/layout-section}}
271 271  
272 +{{layout-section ac:type="two_equal"}}
272 272  {{layout-cell}}
273 -[[image:attach:Kamzik_run(2).PNG]]
274 +**Set run parameters and go 🏃💥**
275 +
276 +1. Set your desired No. of frames
277 +1. Match exposure time with chopper setting
278 +1. Check trigger setting and match to chopper setting
279 +1. Set detector distance to 200.0 mm, confirm with //enter// and click "<Call>" button next to it.
280 +1. To start the run, click "<Call>" next to //exposure time//
281 +
282 +\\
283 +
284 +\\
285 +
286 +**After data collection/Before entering the exp. hutch:**
287 +
288 +1. Go to "Safety" in kamzik.
289 +1. Click "<Call>" next to //prepare_to_open_hutch. //This will automatically:
290 +11. Drive the collimator out
291 +11. Drive the detector back to 1500 mm
292 +1. Close beam shutter BS1 and break door interlock in //P11 XRayFeed //(monitor top left).
293 +
294 +[[image:attach:Screenshot from 2022-04-04 19-36-29.png||height="400"]]
274 274  {{/layout-cell}}
275 -{{/layout-section}}
276 276  
277 -{{layout-section ac:type="single"}}
278 278  {{layout-cell}}
279 -(% class="relative-table wrapped" style="width: 55.9569%;" %)
298 +(% class="wrapped relative-table" style="width: 100.0%;" %)
280 280  |=(((
281 281  Parameter
282 282  )))|=(((
... ... @@ -287,7 +287,7 @@
287 287  |(((
288 288  Images number
289 289  )))|(((
290 -number of frames you want to collect
309 +Set number of frames you want to collect
291 291  )))|(% colspan="1" %)(((
292 292  usually 100k - 200k, but adjust according to hitrate
293 293  
... ... @@ -300,7 +300,7 @@
300 300  
301 301  \\
302 302  )))|(% colspan="1" %)(((
303 -chopper at 133 Hz → 7.7 ms (opening time will be 3.7)
322 +chopper at 133 Hz → 3.7 ms
304 304  
305 305  chopper at 66 Hz   → 7.7 ms
306 306  
... ... @@ -322,39 +322,16 @@
322 322  )))|(% colspan="1" %)(((
323 323  \\
324 324  )))
325 -
326 -----
344 +|(% colspan="1" %)(((
345 +move_detector (distance)
346 +)))|(% colspan="1" %)(((
347 +Set detector distance
348 +)))|(% colspan="1" %)(((
349 +200.0 mm   (% style="color: rgb(255,0,0);" %)confirm with //enter//, click "<Call>"
350 +)))
327 327  {{/layout-cell}}
328 328  {{/layout-section}}
329 329  
330 -{{layout-section ac:type="two_equal"}}
331 -{{layout-cell}}
332 -**After data collection/Before entering the exp. hutch:**
333 -
334 -1. Go to "Safety" in kamzik.
335 -1. Click "<Call>" next to //prepare_to_open_hutch. //This will automatically:
336 -11. Drive the collimator out
337 -11. Drive the detector back to 1500 mm
338 -1. Close beam shutter BS1 and break door interlock in //P11 XRayFeed //(monitor top left).
339 -
340 -[[image:attach:Screenshot from 2022-04-04 19-36-29.png]]
341 -{{/layout-cell}}
342 -
343 -{{layout-cell}}
344 -\\
345 -
346 -\\
347 -
348 -\\
349 -
350 -\\
351 -
352 -\\
353 -
354 -[[image:attach:safety_kamzik.PNG]]
355 -{{/layout-cell}}
356 -{{/layout-section}}
357 -
358 358  {{layout-section ac:type="single"}}
359 359  {{layout-cell}}
360 360  ----
Confluence.Code.ConfluencePageClass[0]
Id
... ... @@ -1,1 +1,1 @@
1 -254729378
1 +254726572
URL
... ... @@ -1,1 +1,1 @@
1 -https://confluence.desy.de/spaces/11/pages/254729378/14. Serial Crystallography: CFEL TapeDrive
1 +https://confluence.desy.de/spaces/11/pages/254726572/14. Serial Crystallography: CFEL TapeDrive