Changes for page CFEL TapeDrive: Serial Crystallography

Last modified by chatzies on 2025-11-27 11:35

From 75.1 to 76.1 From 77.1 to 78.1

From version 76.1

edited by ahenkel
on 2022-11-02 16:25

Change comment: There is no comment for this version

To version 77.1

edited by tabermah
on 2024-12-03 11:26

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (3 modified, 0 added, 0 removed)

Details

Page properties

Title

@@ -1,1 +1,1 @@
--14. Serial Crystallography: CFEL TapeDrive
++10. Serial Crystallography: CFEL TapeDrive

Author

@@ -1,1 +1,1 @@
--XWiki.ahenkel
++XWiki.tabermah

Content

@@ -3,11 +3,9 @@
  {{layout-cell}}
  [[image:attach:TapeDrive_beschriftet-tile.jpg||height="400"]]
--\\
  {{toc minLevel="2"/}}
--\\
  ----
@@ -21,11 +21,12 @@
  [[image:attach:20211201_095534.jpg||height="250"]]
--\\
  ----
--== {{id name="14.SerialCrystallography:CFELTapeDrive-14.2ConnectingsampletoElveFlow,sampleexchange"/}}**14.2 Connecting sample to ElveFlow, sample exchange
++== {{id name="14.SerialCrystallography:CFELTapeDrive-14.2ConnectingsampletoElveFlow,sampleexchange"/}}**14.2 Connecting sample to ElveFlow, sample exchange** ==
++
++*
  ** ==
  After filtration, screw the ElveFlow connector to your Eppendorf or Falcon tube. Make sure that the yellow-ish line goes to the bottom of your tube. You can adjust the length by unscrewing the blue fitting on top and pushing/pulling the yellow-ish line. **Don't forget to tigthen the blue fitting afterwards!**
@@ -42,14 +42,15 @@
  [[image:attach:20211201_095232.jpg||height="250"]][[image:attach:20211201_095205.jpg||height="250"]]
--\\
  ----
--== {{id name="14.SerialCrystallography:CFELTapeDrive-14.3TapeDriveoperation"/}}**14.3 TapeDrive operation
++== {{id name="14.SerialCrystallography:CFELTapeDrive-14.3TapeDriveoperation"/}}**14.3 TapeDrive operation** ==
++
++*
  ** ==
--The TapeDrive is controlled through kamzik. To open kamzik, start the server. A terminal will open and shortly after a small window.
++The TapeDrive is controlled through kamzik. To open kamzik, start the server. A terminal will open and shortly after a small window.
  Now start the client. Same thing, a terminal will open, shortly after a small window.
  Click 'Devices' in the **client session** to open the control window.
@@ -61,7 +61,7 @@
  * Change the velocity by typing anything from **0.3-3.0 mm/s**
  * Common velocity is 1.0-1.5 mm/s
  * kamzik displays the used tape in m and %. At 98% the tape will automatically stop since the rolls need to be exchanged at this point.
--\\
++
  * [[image:attach:kamzik_tape.PNG||height="400"]]
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Samplenozzle"/}}**Sample nozzle** ====
@@ -72,16 +72,16 @@
  The absolute position is **not calibrated** and therefore changes after each restart of kamzik.
--(% style="color: rgb(255,0,0);" %)**!!! **(% style="color: rgb(255, 0, 0); color: rgb(0, 0, 0)" %)**During data collection make sure in which direction you are moving, do not move nozzle into beam**(% style="color: rgb(255,0,0);" %)** !!!**(%%)
++(% style="color:#ff0000" %)**!!! **(% style="color:#000000" %)**During data collection make sure in which direction you are moving, do not move nozzle into beam**(% style="color:#ff0000" %)** !!!**(%%)
  \\Adjust the nozzle position by eye until it nearly touches the tape and roughly meets the X-ray interaction point. Then, move to the control hutch to use the on-axis microscope for fine adjustment. Move the nozzle tip to the beam position (red X) and write down the absolut nozzle position. From there move the nozzle in +x to your desired distance.Different distances combined with the tape speed result in several delay times for time-resolved experiments.
  (% class="wrapped" %)
  |=(((
--\\
++
  )))|=(((
  direction
  )))|=(((
--recommended step size
++recommended step size
  for visual adjustment
  )))|=(% colspan="1" %)(((
  recommended step size
@@ -116,8 +116,8 @@
  be careful with -z, tape could be pushed out of focus
  )))
--**
--\\**
++
++
  )))
  * [[image:attach:kamzik_nozzle.PNG||height="400"]]
@@ -125,25 +125,19 @@
  * The chiller circulates fluid through the gas nozzle.
--\\
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Gasnozzle"/}}**Gas nozzle** ====
--\\
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-IRcamera"/}}**IR camera** ====
--\\
  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
                                          xfreerdp +clipboard /size:1920x1080 /u:Cfelusr /v:cfeld-pcx22611
--                                        password: //written on control laptop (changes every 6 months)
--//
++                                        password: //written on control laptop (changes every 6 months)//
--\\
--\\
  ----
@@ -156,7 +156,7 @@
  * Get a new tape roll (bottom left on the cart). **Polypropylen 15 µm**
  * Cut the first cm of the new tape roll, directly behind the black sticky part.
  * Place new roll on roll holder and use sticky tape to attach the end of the old tape to the beginning of the new roll.
--* Open magnetic tape stabilizer on the **left side**. (% style="color: rgb(255,0,0);" %)//!!!BEAMSTOP!!!//
++* Open magnetic tape stabilizer on the **left side**. (% style="color:#ff0000" %)//!!!BEAMSTOP!!!//
  * Start the tape (3mm/s). Once the connetion side has arrived at the collector roll, stop the tape (0mm/s).
  * Again, cut the tape directly behind the connection side. Replace the the old roll with the **empty **one. Old roll can be discarded.
  * Attach new tape to the empty roll by using some sticky tape.
@@ -163,15 +163,11 @@
  * Close tape stabilizer.
  * Reset tape counter in kamzik by clicking "<Call>" in "Main-Tape".
--**[[image:attach:20211201_094101.jpg||height="250"]][[image:attach:20211201_094111.jpg||height="250"]][[image:attach:tape reset.PNG||height="250"]]
--**
++**[[image:attach:20211201_094101.jpg||height="250"]][[image:attach:20211201_094111.jpg||height="250"]][[image:attach:tape reset.PNG||height="250"]]**
--\\
--\\
--**
--**
++
  {{/layout-cell}}
  {{/layout-section}}
@@ -185,13 +185,13 @@
  (% class="code" %)
  (((
--            cd /gpfs/local/shared/ChopperControl
++            cd /gpfs/local/shared/ChopperControl
  )))
  (% class="code" %)
  (((
              python chopperControl.py
--\\\\
++\\
  )))
  {{/layout-cell}}
  {{/layout-section}}
@@ -204,18 +204,17 @@
  {{layout-cell}}
  **Chopper → no Chopper**
--* decrease frequency by max. 10 Hz steps\\
++* decrease frequency by max. 10 Hz steps
  ** click arrow down 10x, "Set", arrow down 10x, "Set", ....
  * at frequency = 10 Hz, click "Stop"
--* set "Hole" to <none> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
++* set "Hole" to <none> (% style="color:#ff0000" %)//Takes some minutes//
--(% style="color: rgb(0,0,0);" %)**no Chopper → Chopper**
++(% style="color:#000000" %)**no Chopper → Chopper**
--* (% style="color: rgb(0,0,0);" %)set "Hole" to <Inner hole (largest)> (% style="color: rgb(255,0,0);" %)//Takes some minutes//
--* (% style="color: rgb(0,0,0);" %)increase frequency by max. 10 Hz steps
--** (% style="color: rgb(0,0,0);" %)click arrow up 10x, "Set", arrow up 10x, "Set", .....
--* (% style="color: rgb(0,0,0);" %)//usually 130 Hz, results in exposure time of 3.7 ms (technical exposure will always be 7.7 ms, since max. frame rate is 130 Hz
--//
++* (% style="color:#000000" %)set "Hole" to <Inner hole (largest)> (% style="color:#ff0000" %)//Takes some minutes//
++* (% style="color:#000000" %)increase frequency by max. 10 Hz steps
++** (% style="color:#000000" %)click arrow up 10x, "Set", arrow up 10x, "Set", .....
++* (% style="color:#000000" %)//usually 130 Hz, results in exposure time of 3.7 ms (technical exposure will always be 7.7 ms, since max. frame rate is 130 Hz//
  {{/layout-cell}}
  {{/layout-section}}
@@ -235,7 +235,7 @@
                                 //>>usually the terminal is open, just repeat previous command with arrow up, enter and type in the password//
--\\
++
  {{/layout-cell}}
  {{/layout-section}}
@@ -243,22 +243,19 @@
  {{layout-cell}}
  **Check list:**
--(% style="color: rgb(255,0,0);" %)//always after entering the hutch!//
++(% style="color:#ff0000" %)//always after entering the hutch!//
--(% style="color: rgb(0,0,0);" %)Click "Run" icon in kamzik.
++(% style="color:#000000" %)Click "Run" icon in kamzik.
--* Put detector distance 200 in //prepare_for_measurement (      )
--//
--* Click "<Call>" next to //prepare_for_measurement
--//This will:\\
++* Put detector distance 200 in //prepare_for_measurement (      )//
++* Click "<Call>" next to //prepare_for_measurement//
++This will:
  ** drive the collimator in //IN// position
  ** drive detector to 200 mm
--\\
--* Open beam shutter BS1 in //CrystalControl //or// P11 XRayFeed //
++* Open beam shutter BS1 in //CrystalControl //or// P11 XRayFeed //
--\\
  //**Set run parameters and go 🏃💥**//
@@ -266,9 +266,8 @@
 . Enter the protein ID of your crystal sample
 . Match exposure time with chopper setting or set desired exposure time
 . Check trigger setting and match to chopper setting
--no chopper → external triffer //off
--//     chopper → external trigger// on
--//
++no chopper → external triffer //off//
++    chopper → external trigger// on//
 . To start the run, click "<Call>" next to //start_run (exposure    )//
  {{/layout-cell}}
@@ -279,7 +279,7 @@
  {{layout-section ac:type="single"}}
  {{layout-cell}}
--(% class="relative-table wrapped" style="width: 55.9569%;" %)
++(% class="relative-table wrapped" style="width:55.9569%" %)
  |=(((
  Parameter
  )))|=(((
@@ -301,7 +301,7 @@
  )))|(((
  exposure time of Eiger
--\\
++
  )))|(% colspan="1" %)(((
  with chopper         → opening time displayed in chopper GUI
  no chopper            → 7.7 ms
@@ -313,7 +313,7 @@
  )))|(((
  changes automatically
  )))|(% colspan="1" %)(((
--\\
++
  )))
  |(% colspan="1" %)(((
  Detector distance
@@ -320,7 +320,7 @@
  )))|(% colspan="1" %)(((
  current detector postion readout
  )))|(% colspan="1" %)(((
--\\
++
  )))
  |(% colspan="1" %)(((
  protein ID
@@ -327,7 +327,7 @@
  )))|(% colspan="1" %)(((
  protein ID of crystal sample (see AMARCORD)
  )))|(% colspan="1" %)(((
--\\
++
  )))
  ----
@@ -348,15 +348,11 @@
  {{/layout-cell}}
  {{layout-cell}}
--\\
++
--\\
--\\
--\\
--\\
  [[image:attach:safety_kamzik.PNG]]
  {{/layout-cell}}
@@ -375,7 +375,6 @@
  * motor connected (icon green)?
  )))
--\\
  * (((
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Nozzlemotorsarenotresponding"/}}Nozzle motors are not responding ====
@@ -385,7 +385,6 @@
  * motor limits reached? → position displayed in red
  )))
--\\
  * (((
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
@@ -395,7 +395,6 @@
  * Nozzle or lines clogged? → flush with water, change nozzle
  )))
--\\
  * (((
  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Simplonfilewriter/eigerstreamissues"/}}Simplon filewriter/eiger stream issues ====
@@ -403,12 +403,15 @@
  * First, restart kamzik (server+client) and see if this solves the issue
  * If not, restart the Simplon server (in Astor → haspp11exp03, right click on Simplon/EH.1 and restart)
  * (((
--If nothing works, kill the Simplon process and then start the server again:* (((
++If nothing works, kill the Simplon process and then start the server again:*
++
++(((
  (% class="code" %)
  (((
  ssh haspp11exp03
  )))
  )))
++
  * (((
  (% class="code" %)
  (((
@@ -429,7 +429,7 @@
  {{layout-section ac:type="single"}}
  {{layout-cell}}
--\\
++
  {{/layout-cell}}
  {{/layout-section}}
  {{/layout}}

Changes for page CFEL TapeDrive: Serial Crystallography

Summary

Details

Applications

Navigation