Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 78.1
edited by tabermah
on 2024-12-03 11:34
Change comment: There is no comment for this version
To version 77.1
edited by tabermah
on 2024-12-03 11:26
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,1 +1,1 @@
1 -08. Serial Crystallography: CFEL TapeDrive
1 +10. Serial Crystallography: CFEL TapeDrive
Content
... ... @@ -24,7 +24,7 @@
24 24  
25 25  == {{id name="14.SerialCrystallography:CFELTapeDrive-14.2ConnectingsampletoElveFlow,sampleexchange"/}}**14.2 Connecting sample to ElveFlow, sample exchange** ==
26 26  
27 -*
27 +*
28 28  ** ==
29 29  
30 30  After filtration, screw the ElveFlow connector to your Eppendorf or Falcon tube. Make sure that the yellow-ish line goes to the bottom of your tube. You can adjust the length by unscrewing the blue fitting on top and pushing/pulling the yellow-ish line. **Don't forget to tigthen the blue fitting afterwards!**
... ... @@ -46,7 +46,7 @@
46 46  
47 47  == {{id name="14.SerialCrystallography:CFELTapeDrive-14.3TapeDriveoperation"/}}**14.3 TapeDrive operation** ==
48 48  
49 -*
49 +*
50 50  ** ==
51 51  
52 52  The TapeDrive is controlled through kamzik. To open kamzik, start the server. A terminal will open and shortly after a small window.
... ... @@ -116,6 +116,7 @@
116 116  be careful with -z, tape could be pushed out of focus
117 117  )))
118 118  
119 +
119 119  
120 120  )))
121 121  * [[image:attach:kamzik_nozzle.PNG||height="400"]]
... ... @@ -124,6 +124,7 @@
124 124  
125 125  * The chiller circulates fluid through the gas nozzle.
126 126  
128 +
127 127  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Gasnozzle"/}}**Gas nozzle** ====
128 128  
129 129  
... ... @@ -240,8 +240,10 @@
240 240  ** drive the collimator in //IN// position
241 241  ** drive detector to 200 mm
242 242  
245 +
243 243  * Open beam shutter BS1 in //CrystalControl //or// P11 XRayFeed //
244 244  
248 +
245 245  //**Set run parameters and go 🏃💥**//
246 246  
247 247  1. Set your desired No. of frames
... ... @@ -352,6 +352,7 @@
352 352  * motor connected (icon green)?
353 353  )))
354 354  
359 +
355 355  * (((
356 356  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Nozzlemotorsarenotresponding"/}}Nozzle motors are not responding ====
357 357  
... ... @@ -360,6 +360,7 @@
360 360  * motor limits reached? → position displayed in red
361 361  )))
362 362  
368 +
363 363  * (((
364 364  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Sampleflowisnotrespondingtohigherpressure"/}}Sample flow is not responding to higher pressure ====
365 365  
... ... @@ -368,6 +368,7 @@
368 368  * Nozzle or lines clogged? → flush with water, change nozzle
369 369  )))
370 370  
377 +
371 371  * (((
372 372  ==== {{id name="14.SerialCrystallography:CFELTapeDrive-Simplonfilewriter/eigerstreamissues"/}}Simplon filewriter/eiger stream issues ====
373 373