Skip to Content
Last modified by chatzies on 2025-11-27 11:35
From version 81.1
edited by tabermah
on 2024-12-10 15:21
Change comment: There is no comment for this version
To version 80.1
edited by tabermah
on 2024-12-10 15:20
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,7 +9,7 @@
9 9  
10 10  ----
11 11  
12 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.1Samplecharacteristicsandpreparation"/}}8.1. Sample characteristics and preparation =
12 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.1Samplecharacteristicsandpreparation"/}}8.1 Sample characteristics and preparation =
13 13  
14 14  suspension of microcrystals, **at least** 200 µL with 20% crystal density (more is always better), size range: 2-30 µm, **tip:** bring some mother liquor for washing, filtering, diluting etc.
15 15  
... ... @@ -22,9 +22,9 @@
22 22  
23 23  ----
24 24  
25 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.2ConnectingsampletoElveFlow,sampleexchange"/}}8.2. Connecting sample to ElveFlow, sample exchange =
25 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.2ConnectingsampletoElveFlow,sampleexchange"/}}8.2 Connecting sample to ElveFlow, sample exchange =
26 26  
27 -*
27 +*
28 28  ** ==
29 29  
30 30  After filtration, screw the ElveFlow connector to your Eppendorf or Falcon tube. Make sure that the yellow-ish line goes to the bottom of your tube. You can adjust the length by unscrewing the blue fitting on top and pushing/pulling the yellow-ish line. **Don't forget to tigthen the blue fitting afterwards!**
... ... @@ -44,9 +44,9 @@
44 44  
45 45  ----
46 46  
47 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.3TapeDriveoperation"/}}8.3. TapeDrive operation =
47 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.3TapeDriveoperation"/}}8.3 TapeDrive operation =
48 48  
49 -*
49 +*
50 50  ** ==
51 51  
52 52  The TapeDrive is controlled through kamzik. To open kamzik, start the server. A terminal will open and shortly after a small window.
... ... @@ -139,7 +139,7 @@
139 139  
140 140  ----
141 141  
142 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.4Taperollexchange"/}}8.4. Tape roll exchange =
142 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.4Taperollexchange"/}}8.4 Tape roll exchange =
143 143  
144 144  The tape stops automatically at 98% used length, if you need to change the rolls for orther reasons, stop the tape (velocity = 0.0 mm/s).
145 145  
... ... @@ -167,7 +167,7 @@
167 167  {{layout-cell}}
168 168  ----
169 169  
170 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.5Chopper"/}}8.5. Chopper =
170 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.5Chopper"/}}8.5 Chopper =
171 171  
172 172  start chopper gui from terminal:
173 173  
... ... @@ -210,7 +210,7 @@
210 210  {{layout-cell}}
211 211  ----
212 212  
213 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.6Datacollection"/}}8.6. Data collection =
213 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.6Datacollection"/}}8.6 Data collection =
214 214  
215 215  Once the hutch is interlocked, set remote control to the TapeDrive laptop by opening a terminal and executing the following command:
216 216  
... ... @@ -343,7 +343,7 @@
343 343  {{layout-cell}}
344 344  ----
345 345  
346 -= {{id name="14.SerialCrystallography:CFELTapeDrive-14.7Troubleshooting"/}}8.7. Troubleshooting =
346 += {{id name="14.SerialCrystallography:CFELTapeDrive-14.7Troubleshooting"/}}8.7 Troubleshooting =
347 347  
348 348  * (((
349 349  == {{id name="14.SerialCrystallography:CFELTapeDrive-Tapestopped"/}}Tape stopped ==