Changes for page Trigger Howto

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -5,82 +5,43 @@
5	5	= Introduction (user panel)
6	6	=
7	7
8		-The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 1 ns steps (over many ms), one can choose between 10 Hz triggers, frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]].
	8	+The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 9 ns steps, One can choose between 10 Hz triggers, Triggers connected to the (fast) FEL shutters,  frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]] ([[Design Paper>>url:http://ttfinfo2.desy.de/doocs/Timing/CDRv2.2short.pdf||shape="rect"]]).
9	9
10		-in short: the triggers are for low impedance (~~50 OHM terminated ?? ), 5V triggers with an adjustable width. The main control panel for the x2 timer has the control options for the 3 front modules (connected with a RJ45 cable - connecting to a "trigger box" with 2 trigger exits (Lemo) each) and 8 Lemo exits at the back of the crate. in the BL-beamline case these triggers are connected to the BNC (patch panel) ports at the rack.
	10	+In short:
11	11
12		-The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses and not in respect to some (arbitrary) reference time ( Event)[[~[~[image:url:http://hasfweb.desy.de/pub/Setup/TriggerHowto/Trigger_scheme.gif~|~|alt="Trigger_scheme.gif" width="800"~]~]>>attach:Trigger_scheme.gif]]
	12	+* the triggers are for low impedance (~~50 Ohm )
	13	+* signal level is + 5V - otherwise 0V (in the expert panel one can also invert the signal - base line is +5 V and trigger 0V)
	14	+* The trigger are send to the MTCA several ms before the first FEL pulse (3.1 ms for the "standard" trigger, 21.5 ms for the "early" trigger).
	15	+* The timer card can delay the trigger in 9 ns  steps for more than 100 ms (an option to shift the trigger in 1 ns steps is available in the expert panel)
	16	+* The shown delay in µs is in respect to the //first// FEL pulse. negative delay: trigger comes before FEL, positive : trigger comes after the FEL.
	17	+* The desired delay has to be entered in the "delay to be set" field and as second step pressing the "set delay" sends the delay value to the timer card. Then the trigger delay will be changed and the "actual delay" will be updated.
	18	+* The trigger can be set to only provide a trigger signal if the FEL Fast shutter is open. One has to choose which FEL shutter to use.
	19	+* The trigger  width can be adjusted from 9 ns to several ms in 9 ns steps
	20	+* The timer card can in addition to the 10 Hz triggers also provide frequencies which are linked to the FEL repetition rate and the actual burst pattern of the FEL. For details how to set these modes see below
	21	+* At the beamlines the triggers are provided with a  BNC patch panel
13	13
	23	+The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses (and not in respect to some arbitrary event time)
14	14
	25	+
15	15	\\
16	16
17		-= Different trigger events (starting points) =
	28	+[[image:attach:image2020-1-23_12-10-59.png||width="700"]]
18	18
19		-one can configure each channel for an individual trigger event
	30	+\\
20	20
21		-**FLASH1**
	32	+\\
22	22
23		-(% class="wrapped" %)
24		-|(((
25		-trigger No
26		-)))|(((
27		-function
28		-)))
29		-|(((
30		-16
31		-)))|(((
32		-the MCA trigger 3.11 ms before the Flash1 pulses (same as A6 but more stable)
33		-)))
34		-|(((
35		-166
36		-)))|(((
37		-A6 event. still possible to use but less precise than 16
38		-)))
39		-|(((
40		-162
41		-)))|(((
42		-A2 event as earliest ( 24 ms before the FEL)
43		-)))
44		-|(((
45		-224
46		-)))|(((
47		-E0 event of the BL fast shutter ( 19 ms before the FEL)
48		-)))
49		-|(((
50		-225
51		-)))|(((
52		-E1 event of the PG fast shutter ( 19 ms before the FEL)
53		-)))
54		-|(((
55		-21
56		-)))|(((
57		-Trig16 + first bunch of FLASH1 - this trigger is shifted when FL1 starts later than "700"
58		-)))
	34	+Choosing a FLASH1 trigger there are 2 options to be synchronized with the BL and the PG shutter :
59	59
60		-\\
	36	+ [[image:attach:image2020-1-23_12-29-40.png||height="250"]]
61	61
62		-\\
	38	+A yellow background indicates that the trigger is synchronized to a fast shutter:
63	63
64		-**FLASH2**
	40	+[[image:attach:image2020-1-23_12-31-41.png||height="250"]] or:[[image:attach:image2020-1-23_12-32-20.png||height="250"]]
65	65
66		-(% class="wrapped" %)
67		-|(((
68		-trigger No
69		-)))|(((
70		-function
71		-)))
72		-|(((
73		-22
74		-)))|(((
75		-Trig116 + first bunch of FLASH2 - this trigger is shifted when FL2 starts at a different start time
76		-)))
77		-|(((
78		-181
79		-)))|(((
80		-shifts with the start time of FLASH2 as event 22 but comes 22 ms ! before the FEL
81		-)))
	42	+\\
82	82
83		-from this trigger as starting point one can shift the timing in 9 ns steps first and finally in 0.9 ns steps for fine adjustment.
	44	+\\
84	84
85	85	\\
86	86
...	...	@@ -88,7 +88,7 @@
88	88
89	89	\\
90	90
91		-[[image:attach:image2019-9-17_13-10-56.png||height="250"]] [[image:attach:image2019-9-17_13-8-46.png||height="400"]]
	52	+[[image:attach:image2020-1-23_12-28-6.png||height="250"]] [[image:attach:image2019-9-17_13-8-46.png||height="400"]]
92	92
93	93	With the **"Expert overview"** one gets the overview over all channels available on the timing card and can configure the card. This is useful to look what channels are using clock settings or burst mode settings that one wants to change ... and using the other tabs one can set parameters for clocks and bursts (see below)
94	94
...	...	@@ -96,14 +96,12 @@
96	96
97	97	For each trigger channel there is in addition an **"Expert panel"** to set the properties of THIS channel
98	98
99		-[[image:attach:image2019-9-17_13-14-52.png||height="250"]] [[image:attach:image2019-9-17_13-15-38.png||width="550"]]
	60	+[[image:attach:image2020-1-23_12-28-46.png||height="250"]] [[image:attach:image2019-9-17_13-15-38.png||width="550"]]
100	100
101	101	\\
102	102
103	103	\\
104	104
105		-\\
106		-
107	107	= Set a constant frequency to a channel =
108	108
109	109	=
...	...	@@ -153,70 +153,214 @@
153	153
154	154	\\
155	155
	115	+== General FLASH frequencies: ==
	116	+
156	156	\\
157	157
	119	+(% class="relative-table wrapped" style="width: 19.422%;" %)
	120	+|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
	121	+(% style="color: rgb(0,0,0);" title="" %)**Name
	122	+**
	123	+)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
	124	+(% style="color: rgb(0,0,0);" title="" %)**Frequency
	125	+**
	126	+)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
	127	+(% style="color: rgb(0,0,0);" title="" %)**Divider**
	128	+)))
	129	+|(((
	130	+1.3 GHz
	131	+)))|(((
	132	+1300.000000 MHz
	133	+)))|(((
158	158	\\
	135	+)))
	136	+|(((
	137	+108 MHz
	138	+)))|(((
	139	+108.333333 MHz
	140	+)))|(((
	141	+12
	142	+)))
	143	+|(((
	144	+9 MHz
	145	+)))|(((
	146	+9.02777777 MHz
	147	+)))|(((
	148	+144
	149	+)))
	150	+|(((
	151	+4.5 MHz
	152	+)))|(((
	153	+4.513888 MHz
	154	+)))|(((
	155	+288
	156	+)))
	157	+|(((
	158	+1 MHz
	159	+)))|(((
	160	+1.003086 MHz
	161	+)))|(((
	162	+1296
	163	+)))
159	159
160	160	\\
161	161
162	162	Once a clock is configured with the right frequency one can choose in the "expert panel" of the according channel the "FPGA clock" in the "input source select"  chooser.
163	163
164		-\\
	169	+One has to set the delay to values less than the repetition rate ... (so for 1 MHz between 0 and 990 µs)  and the trigger width also less than the rep rate ...
165	165
166		-\\
	171	+This results in a continuous train of pulses with the set trigger width.
167	167
	173	+= Creating an (own) burst trigger =
	174	+
	175	+One can use now a SECOND trigger channel which is set to a regular 10 Hz trigger  and gate the clock output to create a burst with defined start point and length,
	176	+
	177	+For the example we use the FRONT.TRG2 (BL3 Trg5) as gate pulse which defines the length of the burst (set with the trigger width) and the (rough) starting point of the burst. This trigger is only used as gate and the physical trigger output is NOT used.
	178	+
	179	+The  second channel (here FRONT.TRG3 (BL3 Trg6) which is set to the clock frequency defines the reprate (by the FPGA clock setting) , the exact starting point of the first trigger ( by the delay ) and the width of the  MHz/kHz triggers (width).
	180	+
	181	+**To get from the clock to the burst trigger** one has to:
	182	+
	183	+* set the  "2nd source select" to the gate trigger ( here FRONT.TRG2) - this defines a second source to considder for the trigger output.
	184	+* and the "output source select" to "AND 2nd Ch."  this finally only sends a trigger if on both inputs (clock and gate) we have a high signal.
	185	+
168	168	\\
169	169
170		-One has to set the delay to values less than the repetition rate ... (so for 1 MHz between 0 and 990 µs)  and the trigger width also less than the rep rate ...
	188	+[[image:attach:image2019-9-17_14-35-5.png||height="250"]] [[image:attach:image2019-9-17_14-34-38.png||width="400"]]
171	171
172	172	\\
173	173
174	174	\\
175	175
	194	+= Real bunch trigger  - get a trigger for each FEL pulse =
	195	+
176	176	\\
177	177
178		-This results in a continuous train of pulses with the set trigger width :
	198	+Sometimes it is convenient to get a trigger pulse for each pulse in the FEL. thus if the FEL number of bunches or reprate are changed, the trigger adapts accordingly.
179	179
180		-= Creating an (own) burst trigger =
	200	+For this one has to select the source of interest in the expert overview panel (tab: "Bunch pattern") ... well for us this is FLASH1 (FL1D) or FLASH2 (FL2D)
181	181
182		-One can use now a SECOND trigger channel which is set to a regular 10 Hz trigger  and gate the clock output to create a burst with defined start point and length,
	202	+There are 6 different bunch pattern "channels" one can configure. Typically only 2 are needed ... And in each one there are 6 selectors to choose sources . We only need one - it does not matter in which one is used.
183	183
184		-\\
	204	+[[~[~[image:attach:image2019-9-17_14-51-28.png~|~|height="250"~]~]>>attach:image2019-9-17_14-51-28.png]][[image:attach:image2019-9-17_14-47-15.png||thumbnail="true" height="199"]]
185	185
186	186	\\
187	187
188		-\\
	208	+In the expert panel one can now choose the configured "Bunch Pattern" as "Input source select"
189	189
190		-\\
	210	+**NOTE: To shift the burst in time one can no longer use the delay of the individual channel BUT the delay in the "Bunch pattern" tab in the expert overview! This now shifts all bursts ... so you better know what you are doing. typically the burst is already shifted to the actual FEL timing ... Shifting the timing should be discussed with the beamline scientist / local contact ...**
191	191
192	192	\\
193	193
	214	+[[image:attach:image2019-9-17_15-4-47.png||height="250"]][[image:attach:image2019-9-17_14-52-40.png||height="250"]]
	215	+
194	194	\\
195	195
196	196	\\
197	197
198		-* in order to generate a stable frequency one has to set the input source to FPGA clock (and use dividers to get the desired frequency)
199		-* to generate the burst patterns of the FEL one has to choose a trigger event (best 116 for FLASH 2 and 16 for FLASH1) and activate Destination 1 for FLASH1 and Destination 2 for FLASH2 . finally one has to assign the activated Bunch pattern mask to the trigger channel of choice . now the pattern can be shifted and the trigger width can be changed as with the 10 Hz triggers. **IMPORTANT: to move the bunchtrain to the desired starting point the DELAY in the expert panel (see below) has to be used. The Trigger in the user panel (see above) has to be set to 0 !!!**
200		-[[~[~[image:url:http://hasfweb.desy.de/pub/Setup/TriggerHowto/mtcatrigger2k.png~|~|alt="mtcatrigger2k.png" width="607" height="458"~]~]>>attach:mtcatrigger2k.png]]
	220	+= Different trigger events (starting points) =
201	201
202		-here an example defining the bunch pattern for FLASH1 to mask 1
	222	+one can configure each channel for an individual trigger event
203	203
204		-\\
	224	+**FLASH1**
205	205
206		-\\
	226	+(% class="wrapped" %)
	227	+|(((
	228	+trigger No
	229	+)))|(((
	230	+function
	231	+)))
	232	+|(% colspan="1" %)(((
	233	+21
	234	+)))|(% colspan="1" %)(((
	235	+Trig16 + first bunch of FLASH1 - this trigger is shifted when FL1 starts later than "700"
	236	+)))
	237	+|(% colspan="1" %)(((
	238	+180
	239	+)))|(% colspan="1" %)(((
	240	+shifts with the start time of FLASH1 as event 21 but comes 23 ms  before the FEL
	241	+)))
	242	+|(((
	243	+16
	244	+)))|(((
	245	+the MCA trigger 3.11 ms before the Flash1 pulses (same as A6 but more stable)
	246	+)))
	247	+|(((
	248	+166
	249	+)))|(((
	250	+A6 event. still possible to use but less precise than 16
	251	+)))
	252	+|(((
	253	+162
	254	+)))|(((
	255	+A2 event as earliest ( 24 ms before the FEL)
	256	+)))
	257	+|(((
	258	+224
	259	+)))|(((
	260	+E0 event of the BL fast shutter ( 19 ms before the FEL) - to be switched off in 2020
	261	+)))
	262	+|(((
	263	+225
	264	+)))|(((
	265	+E1 event of the PG fast shutter ( 19 ms before the FEL) - to be switched off in 2020
	266	+)))
207	207
208	208	\\
209	209
210	210	\\
211	211
	272	+**FLASH2**
	273	+
	274	+(% class="wrapped" %)
	275	+|(((
	276	+trigger No
	277	+)))|(((
	278	+function
	279	+)))
	280	+|(((
	281	+22
	282	+)))|(((
	283	+Trig116 + first bunch of FLASH2 - this trigger is shifted when FL2 starts at a different start time
	284	+)))
	285	+|(((
	286	+181
	287	+)))|(((
	288	+shifts with the start time of FLASH2 as event 22 but comes 23 ms  before the FEL
	289	+)))
	290	+
	291	+from this trigger as starting point one can shift the timing in 9 ns steps first and finally in 0.9 ns steps for fine adjustment.
	292	+
212	212	\\
213	213
214	214	\\
215	215
	297	+= Info about the Fast shutter trigger =
	298	+
	299	+Since Jan 2020 the fast shutter trigger at FLASH1 is generated via local inhibit at the EXP1 and EXP2 crate and not via E0 and E1 events anymore
	300	+
	301	+for details see [[doc:FLASH.Fast Shutter trigger inhibit system]]
	302	+
216	216	\\
217	217
	305	+== Special trigger options for the fast shutter: ==
	306	+
	307	+=== Fast shutter inhibit signal ===
	308	+
	309	+It is possible to have the fast shutter inhibit signal (the signal coming from the fast shutter to the inhibit boxes connected to the X2 cards) directly available for users. For this one can select the output source as 2nd channel:
	310	+
	311	+[[image:attach:image2020-2-5_10-59-41.png||height="250"]]
	312	+
218	218	\\
219	219
	315	+=== Inverse fast shutter trigger ===
	316	+
	317	+If one wants to have an inverse fast shutter trigger (10 Hz signal that comes only if the fast shutter is** CLOSED**) one can use a T and a small Lemo cable to double the input from the fast shutter  to another input at the inhibit box.
	318	+
	319	+In the FL2 case input1 is the regular fast shutter channel and input2 is usually not used. for this additional input one can set the input configuration to **inverse:**
	320	+
	321	+[[image:attach:image2020-2-5_14-11-55.png||height="400"]]
	322	+
220	220	\\
221	221
222	222	\\