Changes for page Trigger Howto

Last modified by sndueste on 2023/07/07 11:28
From version 15.1
edited by sndueste
on 2020/01/21 12:57
Change comment: There is no comment for this version
To version 23.1
edited by sndueste
on 2020/01/23 16:18
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -5,90 +5,51 @@
5 5  = Introduction (user panel)
6 6   =
7 7  
8 -The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 1 ns steps (over many ms), one can choose between 10 Hz triggers, frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]] ([[Design Paper>>url:http://ttfinfo2.desy.de/doocs/Timing/CDRv2.2short.pdf||shape="rect"]]).
8 +The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 9 ns steps, One can choose between 10 Hz triggers, Triggers connected to the (fast) FEL shutters,  frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]] ([[Design Paper>>url:http://ttfinfo2.desy.de/doocs/Timing/CDRv2.2short.pdf||shape="rect"]]).
9 9  
10 -in short: the triggers are for low impedance (~~50 OHM terminated ?? ), 5V triggers with an adjustable width. The main control panel for the x2 timer has the control options for the 3 front modules (connected with a RJ45 cable - connecting to a "trigger box" with 2 trigger exits (Lemo) each) and 8 Lemo exits at the back of the crate. in the BL-beamline case these triggers are connected to the BNC (patch panel) ports at the rack.
10 +In short:
11 11  
12 -The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses and not in respect to some (arbitrary) reference time ( Event)
12 +* the triggers are for low impedance (~~50 Ohm )
13 +* signal level is + 5V - otherwise 0V (in the expert panel one can also invert the signal - base line is +5 V and trigger 0V)
14 +* The trigger are send to the MTCA several ms before the first FEL pulse (3.1 ms for the "standard" trigger, 23 ms for the "early" trigger).
15 +* The timer card can delay the trigger in 9 ns  steps for more than 100 ms (an option to shift the trigger in 1 ns steps is available in the expert panel)
16 +* The shown delay in µs is in respect to the //first// FEL pulse. negative delay: trigger comes before FEL, positive : trigger comes after the FEL.
17 +* The desired delay has to be entered in the "delay to be set" field and as second step pressing the "set delay" sends the delay value to the timer card. Then the trigger delay will be changed and the "actual delay" will be updated.
18 +* The trigger can be set to only provide a trigger signal if the FEL Fast shutter is open. One has to choose which FEL shutter to use.
19 +* The trigger  width can be adjusted from 9 ns to several ms in 9 ns steps
20 +* The timer card can in addition to the 10 Hz triggers also provide frequencies which are linked to the FEL repetition rate and the actual burst pattern of the FEL. For details how to set these modes see below
21 +* At the beamlines the triggers are provided with a  BNC patch panel
13 13  
14 -[[image:attach:Trigger_scheme.gif]]
15 -\\
23 +The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses (and not in respect to some arbitrary event time)
16 16  
17 -= Different trigger events (starting points) =
18 18  
19 -one can configure each channel for an individual trigger event
26 +\\
20 20  
21 -**FLASH1**
28 +[[image:attach:image2020-1-23_12-10-59.png||width="700"]]
22 22  
23 -(% class="wrapped" %)
24 -|(((
25 -trigger No
26 -)))|(((
27 -function
28 -)))
29 -|(((
30 -16
31 -)))|(((
32 -the MCA trigger 3.11 ms before the Flash1 pulses (same as A6 but more stable)
33 -)))
34 -|(((
35 -166
36 -)))|(((
37 -A6 event. still possible to use but less precise than 16
38 -)))
39 -|(((
40 -162
41 -)))|(((
42 -A2 event as earliest ( 24 ms before the FEL)
43 -)))
44 -|(((
45 -224
46 -)))|(((
47 -E0 event of the BL fast shutter ( 19 ms before the FEL)
48 -)))
49 -|(((
50 -225
51 -)))|(((
52 -E1 event of the PG fast shutter ( 19 ms before the FEL)
53 -)))
54 -|(((
55 -21
56 -)))|(((
57 -Trig16 + first bunch of FLASH1 - this trigger is shifted when FL1 starts later than "700"
58 -)))
59 -
60 60  \\
61 61  
62 62  \\
63 63  
64 -**FLASH2**
34 +Choosing a FLASH1 trigger there are 2 options to be synchronized with the BL and the PG shutter :
65 65  
66 -(% class="wrapped" %)
67 -|(((
68 -trigger No
69 -)))|(((
70 -function
71 -)))
72 -|(((
73 -22
74 -)))|(((
75 -Trig116 + first bunch of FLASH2 - this trigger is shifted when FL2 starts at a different start time
76 -)))
77 -|(((
78 -181
79 -)))|(((
80 -shifts with the start time of FLASH2 as event 22 but comes 22 ms ! before the FEL
81 -)))
36 + [[image:attach:image2020-1-23_12-29-40.png||height="250"]]
82 82  
83 -from this trigger as starting point one can shift the timing in 9 ns steps first and finally in 0.9 ns steps for fine adjustment.
38 +A yellow background indicates that the trigger is synchronized to a fast shutter:
84 84  
40 +[[image:attach:image2020-1-23_12-31-41.png||height="250"]] or:[[image:attach:image2020-1-23_12-32-20.png||height="250"]]
41 +
85 85  \\
86 86  
44 +\\
45 +
46 +\\
47 +
87 87  = Expert panels =
88 88  
89 89  \\
90 90  
91 -[[image:attach:image2019-9-17_13-10-56.png||height="250"]] [[image:attach:image2019-9-17_13-8-46.png||height="400"]]
52 +[[image:attach:image2020-1-23_12-28-6.png||height="250"]] [[image:attach:image2019-9-17_13-8-46.png||height="400"]]
92 92  
93 93  With the **"Expert overview"** one gets the overview over all channels available on the timing card and can configure the card. This is useful to look what channels are using clock settings or burst mode settings that one wants to change ... and using the other tabs one can set parameters for clocks and bursts (see below)
94 94  
... ... @@ -96,7 +96,7 @@
96 96  
97 97  For each trigger channel there is in addition an **"Expert panel"** to set the properties of THIS channel
98 98  
99 -[[image:attach:image2019-9-17_13-14-52.png||height="250"]] [[image:attach:image2019-9-17_13-15-38.png||width="550"]]
60 +[[image:attach:image2020-1-23_12-28-46.png||height="250"]] [[image:attach:image2019-9-17_13-15-38.png||width="550"]]
100 100  
101 101  \\
102 102  
... ... @@ -155,13 +155,15 @@
155 155  
156 156  \\
157 157  
158 -(% class="relative-table" style="width: 17.2254%;" %)
159 -|(((
160 -(% style="color: rgb(0,0,255);" %)Name
161 -)))|(((
162 -(% style="color: rgb(0,0,255);" %)Frequency
163 -)))|(((
164 -(% style="color: rgb(0,0,255);" %)Divider
119 +(% class="relative-table wrapped" style="width: 19.422%;" %)
120 +|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
121 +(% style="color: rgb(0,0,0);" title="" %)**Name          
122 +**
123 +)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
124 +(% style="color: rgb(0,0,0);" title="" %)**Frequency                
125 +**
126 +)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
127 +(% style="color: rgb(0,0,0);" title="" %)**Divider**
165 165  )))
166 166  |(((
167 167  1.3 GHz
... ... @@ -254,14 +254,97 @@
254 254  
255 255  \\
256 256  
220 += Different trigger events (starting points) =
221 +
222 +one can configure each channel for an individual trigger event
223 +
224 +**FLASH1**
225 +
226 +(% class="wrapped" %)
227 +|(((
228 +trigger No
229 +)))|(((
230 +function
231 +)))
232 +|(% colspan="1" %)(((
233 +21
234 +)))|(% colspan="1" %)(((
235 +Trig16 + first bunch of FLASH1 - this trigger is shifted when FL1 starts later than "700"
236 +)))
237 +|(% colspan="1" %)(((
238 +180
239 +)))|(% colspan="1" %)(((
240 +shifts with the start time of FLASH1 as event 21 but comes 23 ms  before the FEL
241 +)))
242 +|(((
243 +16
244 +)))|(((
245 +the MCA trigger 3.11 ms before the Flash1 pulses (same as A6 but more stable)
246 +)))
247 +|(((
248 +166
249 +)))|(((
250 +A6 event. still possible to use but less precise than 16
251 +)))
252 +|(((
253 +162
254 +)))|(((
255 +A2 event as earliest ( 24 ms before the FEL)
256 +)))
257 +|(((
258 +224
259 +)))|(((
260 +E0 event of the BL fast shutter ( 19 ms before the FEL) - to be switched off in 2020
261 +)))
262 +|(((
263 +225
264 +)))|(((
265 +E1 event of the PG fast shutter ( 19 ms before the FEL) - to be switched off in 2020
266 +)))
267 +
257 257  \\
258 258  
259 259  \\
260 260  
272 +**FLASH2**
273 +
274 +(% class="wrapped" %)
275 +|(((
276 +trigger No
277 +)))|(((
278 +function
279 +)))
280 +|(((
281 +22
282 +)))|(((
283 +Trig116 + first bunch of FLASH2 - this trigger is shifted when FL2 starts at a different start time
284 +)))
285 +|(((
286 +181
287 +)))|(((
288 +shifts with the start time of FLASH2 as event 22 but comes 23 ms  before the FEL
289 +)))
290 +
291 +from this trigger as starting point one can shift the timing in 9 ns steps first and finally in 0.9 ns steps for fine adjustment.
292 +
261 261  \\
262 262  
263 263  \\
264 264  
297 += Info about the Fast shutter trigger =
298 +
299 +Since Jan 2020 the fast shutter trigger at FLASH1 is generated via local inhibit at the EXP1 and EXP2 crate and not via E0 and E1 events anymore
300 +
301 +for details see [[doc:FLASH.Fast Shutter trigger inhibit system]]
302 +
265 265  \\
266 266  
267 267  \\
306 +
307 +\\
308 +
309 +\\
310 +
311 +\\
312 +
313 +\\