Changes for page Trigger Howto

Last modified by sndueste on 2023/07/07 11:28
From version 19.1
edited by sndueste
on 2020/01/23 09:29
Change comment: There is no comment for this version
To version 16.1
edited by sndueste
on 2020/01/21 13:02
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -5,36 +5,15 @@
5 5  = Introduction (user panel)
6 6   =
7 7  
8 -The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 9 ns steps, One can choose between 10 Hz triggers, Triggers connected to the (fast) FEL shutters,  frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]] ([[Design Paper>>url:http://ttfinfo2.desy.de/doocs/Timing/CDRv2.2short.pdf||shape="rect"]]).
8 +The MTCA based triggers have a jitter in the few ps range, the delay can be shifted in 1 ns steps (over many ms), one can choose between 10 Hz triggers, frequencies locked to the pulses (e.g. 1MHz) and the actual bunch patterns. A detailed description can be found in [[x2Timer manual>>attach:x2Timer.pdf]] ([[Design Paper>>url:http://ttfinfo2.desy.de/doocs/Timing/CDRv2.2short.pdf||shape="rect"]]).
9 9  
10 -In short:
10 +in short: the triggers are for low impedance (~~50 OHM terminated ?? ), 5V triggers with an adjustable width. The main control panel for the x2 timer has the control options for the 3 front modules (connected with a RJ45 cable - connecting to a "trigger box" with 2 trigger exits (Lemo) each) and 8 Lemo exits at the back of the crate. in the BL-beamline case these triggers are connected to the BNC (patch panel) ports at the rack.
11 11  
12 -* the triggers are for low impedance (~~50 Ohm )
13 -* signal level is + 5V - otherwise 0V (in the expert panel one can also invert the signal - base line is +5 V and trigger 0V)
14 -* The trigger are send to the MTCA several ms before the first FEL pulse (3.1 ms for the "standard" trigger, 23 ms for the "early" trigger).
15 -* The timer card can delay the trigger in 9 ns  steps for more than 100 ms (an option to shift the trigger in 1 ns steps is available in the expert panel)
16 -* The shown delay in µs is in respect to the //first// FEL pulse. negative delay: trigger comes before FEL, positive : trigger comes after the FEL.
17 -* The desired delay has to be entered in the "delay to be set" field and as second step pressing the "set delay" sends the delay value to the timer card. Then the trigger delay will be changed and the "actual delay" will be updated.
18 -* The trigger can be set to only provide a trigger signal if the FEL Fast shutter is open. One has to choose which FEL shutter to use.
19 -* The trigger  width can be adjusted from 9 ns to several ms in 9 ns steps
20 -* The timer card can in addition to the 10 Hz triggers also provide frequencies which are linked to the FEL repetition rate and the actual burst pattern of the FEL. For details how to set these modes see below
21 -* At the beamlines the triggers are provided with a  BNC patch panel
12 +The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses and not in respect to some (arbitrary) reference time ( Event)
22 22  
23 -The main control can be done with a simplified user panel which can handle the timing in respect to the FEL pulses (and not in respect to some arbitrary event time)
24 -
25 -
14 +[[image:attach:Trigger_scheme.gif]]
26 26  \\
27 27  
28 -\\
29 -
30 -\\
31 -
32 -\\
33 -
34 -\\
35 -
36 -\\
37 -
38 38  = Different trigger events (starting points) =
39 39  
40 40  one can configure each channel for an individual trigger event
... ... @@ -105,8 +105,6 @@
105 105  
106 106  \\
107 107  
108 -\\
109 -
110 110  = Expert panels =
111 111  
112 112  \\
... ... @@ -179,14 +179,12 @@
179 179  \\
180 180  
181 181  (% class="relative-table wrapped" style="width: 19.422%;" %)
182 -|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
183 -(% style="color: rgb(0,0,0);" title="" %)**Name          
184 -**
185 -)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
186 -(% style="color: rgb(0,0,0);" title="" %)**Frequency                
187 -**
188 -)))|(% class="highlight-grey" title="Hintergrundfarbe : Grau" data-highlight-colour="grey" %)(((
189 -(% style="color: rgb(0,0,0);" title="" %)**Divider**
159 +|(((
160 +(% style="color: rgb(0,0,255);" %)Name
161 +)))|(((
162 +(% style="color: rgb(0,0,255);" %)Frequency
163 +)))|(((
164 +(% style="color: rgb(0,0,255);" %)Divider
190 190  )))
191 191  |(((
192 192  1.3 GHz