Changes for page The FLASH HDF5 structure

Last modified by sndueste on 2025/02/06 10:55
From version 70.1
edited by sndueste
on 2023/02/22 09:02
Change comment: There is no comment for this version
To version 67.1
edited by sndueste
on 2022/11/08 18:36
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -79,9 +79,9 @@
79 79  {{/layout-cell}}
80 80  
81 81  {{layout-cell}}
82 -* The //average// FEL pulse energy as example for the **slow** **data**. Here the data is not saved with 10 Hz  - thus not for every FEL pulse train.  The data is typically saved with 1 Hz if the values are changing (like the FEL energy) and every about 20 sec if there is no change for longer time ( e.g. motor set values)
82 +* The //average// FEL pulse energy as example for the **slow** **data** (different e.g. 1 Hz):
83 83  
84 - ( as example only every 10th train ID is listed in the HDF group "index")
84 + ( every 10th train ID is listed in the HDF group "index")
85 85  
86 86  \\
87 87  
... ... @@ -456,78 +456,52 @@
456 456  units: ps (bigger numbers indicate later arrival time of the electrons)
457 457  {{/expand}}
458 458  
459 -====== **BAM FL0.DBC2**{{code language="none"}}{{/code}} ======
460 -
461 -(% style="color: rgb(255,102,0);" %)**DBC2**/electron bunch arrival time  (HDF5 name not yet implemented - see zraw)(%%)
462 -//always saved (PBD)//
463 -**FL0.DBC2**
464 -(% style="color: rgb(0,0,0);" %)channel: FLASH.SDIAG/BAM/**FL0.DBC2**/ARRIVAL_TIME.ABSOLUTE.SA1.COMP (%%)
465 -{{code language="none"}}/FL1/Electron Diagnostic/BAM/ DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIME.ABSOLUTE.SA1.COMPDAQ desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2). The property contains only the arrival time of the bunches sent to FL1 (e.g. if there are 30 bunches in FL1 the first 30 values are the arrival time the remaining numbers should be only 0). These are the same values as the "raw" data below - just "cleaned". The values{{/code}}(% style="font-family: SFMono-Medium , ~"SF Mono~" , ~"Segoe UI Mono~" , ~"Roboto Mono~" , ~"Ubuntu Mono~" , Menlo , Courier , monospace;letter-spacing: 0.0px;" %) show a very good correlation to the arrival time  of the XUV pulses in the experiment (see help).
466 -
467 -{{code language="none"}}units: fs (bigger numbers (typically) indicate later arrival times of the electrons).{{/code}}
468 -
469 -\\
470 -
471 -(% style="color: rgb(255,102,0);" %)DBC2/electron bunch arrival time (raw)  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
459 +(% style="color: rgb(255,102,0);" %)DBC2/electron bunch arrival time{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
472 472  //always saved (PBD)//
473 473  DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE
474 -DAQ channel: (% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE (%%)
475 -desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2). Here the complete bunch train from the FEL is recorded (FLASH1 and FLASH2 pulses). Thus there are values from FLASH 1 in the first part. they may be separated by several "0" values if the reprate is different from 1 MHz ...  - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help). 
462 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE (%%)
463 +desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2) - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help). 
476 476  units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
477 477  
478 478  \\
479 479  
480 -(% style="color: rgb(255,102,0);" %)DBC2/error (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
468 +(% style="color: rgb(255,102,0);" %)DBC2/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
481 481  //always saved (PBD)//
482 482  DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E.bamError(%%)
483 -DAQ channel: (% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMERROR(%%)
471 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMERROR(%%)
484 484  desc: If the value is 0 , the BAM is working well. If it is non-zero there is a problem !!
485 485  
486 486  \\
487 487  
488 -(% style="color: rgb(255,102,0);" %)DBC2/status  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
476 +(% style="color: rgb(255,102,0);" %)DBC2/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
489 489  //always saved (PBD)//
490 490  DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E..bamStatus.//1//(%%)
491 -DAQ channel(% style="color: rgb(0,0,0);" %): FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMSTATUS.1(%%)
479 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMSTATUS(%%)
492 492  desc: (% style="letter-spacing: 0.0px;" %) status bit: 0 - data is valid; 1 - beam present; 2 - calibration ongoing; 3 - feedback enabled; 4 - feedback acting;  mostly check for bit 0 == 1 is sufficient
493 493  
494 494  \\
495 495  
496 -====== **BAM FL1.SFELC**{{code language="none"}}{{/code}} ======
497 -
498 -(% style="font-family: SFMono-Medium , ~"SF Mono~" , ~"Segoe UI Mono~" , ~"Roboto Mono~" , ~"Ubuntu Mono~" , Menlo , Courier , monospace;letter-spacing: 0.0px;" %)/FL1/Electron Diagnostic/BAM/**SFELC**(% style="color: rgb(255,102,0);" %)/electron bunch arrival time  (HDF5 name not yet implemented - see zraw)
499 -
500 -//always saved (PBD)//
501 -(% style="color: rgb(23,43,77);" %)**FL1.SFELC**(%%)
502 -(% style="color: rgb(0,0,0);" %)channel: FLASH.SDIAG/BAM/(% style="color: rgb(0, 0, 0); color: rgb(23, 43, 77)" %)FL1.SFELC(% style="color: rgb(0,0,0);" %)/ARRIVAL_TIME.ABSOLUTE.SA1.COMP
503 -{{code language="none"}} DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIME.ABSOLUTE.SA1.COMPDAQ {{/code}}(% style="letter-spacing: 0.0px;" %)desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020.. The property contains only the arrival time of the bunches sent to FL1 (e.g. if there are 30 bunches in FL1 the first 30 values are the arrival time the remaining numbers should be only 0). These are the same values as the "raw" data below - just "cleaned". The values show a very good correlation to the arrival time  of the XUV pulses in the experiment (see help).
504 -units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
505 -
506 -\\
507 -
508 -\\
509 -
510 -(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/electron bunch arrival time (raw) (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
484 +(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/electron bunch arrival time{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
511 511  //always saved (PBD)//
512 512  DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL1.SFELC(%%)/ARRIVAL_TIME.ABSOLUTE
513 -DAQ channel:** **(% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/FL1.SFELC/ARRIVAL_TIME.ABSOLUTE (%%)
514 -desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020. Here the complete bunch train from the FEL is recorded (FLASH1 and FLASH2 pulses). Thus there are values from FLASH 1 in the first part. they may be separated by several "0" values if the reprate is different from 1 MHz ...  - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help). 
487 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL1.SFELC(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.ABSOLUTE (%%)
488 +desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020.  
515 515  units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
516 516  
517 517  \\
518 518  
519 -(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/error (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
493 +(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
520 520  //always saved (PBD)//
521 521  DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL1.SFELC(%%)/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E.bamError(%%)
522 -DAQ channel(% style="color: rgb(0,0,0);" %): FLASH.SDIAG/BAM/FL1.SFELC/ARRIVAL_TIME.BAMERROR(%%)
496 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL1.SFELC(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.BAMERROR(%%)
523 523  desc: If the value is 0 , the BAM is working well. If it is non-zero there is a problem !!
524 524  
525 525  \\
526 526  
527 -(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/status  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
501 +(% style="color: rgb(23,43,77);" %)SFELC(% style="color: rgb(255,102,0);" %)/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
528 528  //always saved (PBD)//
529 529  DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL1.SFELC(%%)/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E..bamStatus.//1//(%%)
530 -DAQ chann(% style="color: rgb(0,0,0);" %)el: FLASH.SDIAG/BAM/FL1.SFELC/ARRIVAL_TIME.BAMSTATUS.1(%%)
504 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL1.SFELC(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.BAMSTATUS(%%)
531 531  desc: status bit: 0 - data is valid; 1 - beam present; 2 - calibration ongoing; 3 - feedback enabled; 4 - feedback acting;  mostly check for bit 0 == 1 is sufficient
532 532  
533 533  \\
... ... @@ -667,35 +667,14 @@
667 667  FLASH.LASER/FLACPUPGLASER1.PULSEENERGY/DIAG1out/PULSEENERGY.MEAN 
668 668  FLASH.LASER/FLACPUPGLASER1.PULSEENERGY/PG1_incoupl/PULSEENERGY.MEAN 
669 669  FLASH.LASER/FLACPUPGLASER1.PULSEENERGY/PG2_incoupl/PULSEENERGY.MEAN 
644 +
645 +
670 670  FLASH.SYNC/LASER.LOCK.EXP/FLASH1.MOD1.PG.OSC/FMC0.MD22.1.ENCODER_POSITION.RD 
671 671  FLASH.SYNC/LASER.LOCK.EXP/FLASH1.MOD1.PG.OSC/FMC0.MD22.1.ENCODER_POSITION_RAW.RD 
672 672  FLASH.SYNC/LASER.LOCK.EXP/FLASH1.MOD1.PG.OSC/FMC0.MD22.1.POSITION.RD
673 673  
674 -**BL - Hidra laser **
675 -
676 -Property,Units,Description
677 -FLASH.LASER/MODBL.CAM/BL1.13.AC/DAQ_CHANNEL,'AU','FL1HIDRAPP1 Autocorrelation (IR) ROI readout'
678 -FLASH.LASER/MODBL.CAM/BL1.14.VF/DAQ_CHANNEL,'AU','FL1HIDRAPP1 Virtual Focus Camera (IR) ROI readout'
679 -FLASH.LASER/MODBL.SENSORBOARD/PDTRIG_CAMP/DAQ_CHANNEL,'au','FL1PPL Energy channels'
680 -FLASH.LASER/MODBL.SPECT/CAMP_IR/DAQ_CHANNEL,'au','FL1PPL BL Table Spectrum'
681 -FLASH.LASER/HIDRAPP1.SPECTRUM_ANALYSIS/CAMP_IR/DAQ_CHANNEL,'au','FL1PPL Spectrum Analysis'
682 -FLASH.SYNC/LASER.LOCK.EXP/F1.PPL.OSC/FMC0.MD22.1.POSITION.RD,'ps','FL1PPL Optical Delay Line (act)'
683 -FLASH.SYNC/LASER.LOCK.EXP/F1.PPL.OSC/FMC0.MD22.1.POSITION_SET.WR,'ps','FL1PPL Optical Delay Line (set)'
684 -FLASH.SYNC/LASER.LOCK.EXP/F1.PPL.OSC/FMC0.MD22.1.ENCODER_POSITION.RD,'ps','FL1PPL Optical Delay Line (Encoder Readback)'
685 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/CAMP_Delayline/FPOS,'ps','FL1PPL NIR delay BL1 table (act)'
686 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/CAMP_Delayline/FPOS.SET,'ps','FL1PPL NIR delay BL1 table (set)'
687 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/CAMP.ATT/FPOS,'degree','FL1PPL Transmission degree (act)'
688 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/CAMP.ATT/FPOS.SET,'degree','FL1PPL Transmission degree (set)'
689 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/Camp_Focus_Lens/FPOS,'mm','FL1PPL Focus Mirror Stage Position (act)'
690 -FLASH.FEL/FLAPPBEAMLINES.MOTOR/Camp_Focus_Lens/FPOS.SET,'mm','FL1PPL Focus Mirror Stage Position (set)'
691 -FLASH.LASER/MODBL.FEEDFWD/BL1_Att/INPUT.Y,'%','FL1PPL Transmission rate'
692 -FLASH.SYNC/LASER.LOCK.EXP/F1.PPL.OSC/CURRENT_INPUT_JITTER.RD,'fs','FL1PPL Sync. Jitter'
693 -FLASH.SYNC/LASER.LOCK.EXP/F1.PPL.OSC/LOCK_STATUS.VALUE.RD,'au','FL1PPL Sync. Status'
694 -
695 695  \\
696 696  
697 -\\
698 -
699 699  {{expand title="Parameters used until 2021"}}
700 700  {{code language="none"}}/FL1/Experiment/Pump probe laser/laser attenuation{{/code}}
701 701  
... ... @@ -742,6 +742,10 @@
742 742  
743 743  \\
744 744  
698 +\\
699 +
700 +\\
701 +
745 745  [[Contents>>doc:||anchor="Contents"]]
746 746  
747 747  \\
... ... @@ -1072,83 +1072,58 @@
1072 1072  {{/info}}
1073 1073  {{/expand}}
1074 1074  
1075 -\\
1076 -
1077 -====== **BAM FL0.DBC2**{{code language="none"}}{{/code}} ======
1078 -
1079 -(% style="color: rgb(255,102,0);" %)**DBC2**/electron bunch arrival time  (HDF5 name not yet implemented - see zraw)(%%)
1080 -//always saved (PBD)//
1081 -**FL0.DBC2**
1082 -(% style="color: rgb(0,0,0);" %)channel: FLASH.SDIAG/BAM/**FL0.DBC2**/ARRIVAL_TIME.ABSOLUTE.SA2.COMP
1083 -{{code language="none"}}/FL2/Electron Diagnostic/BAM/ DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIME.ABSOLUTE.SA2.COMPDAQ {{/code}}(% style="letter-spacing: 0.0px;" %)desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2). The property contains only the arrival time of the bunches sent to FL2 (e.g. if there are 30 bunches in FL2 the first 30 values are the arrival time the remaining numbers should be only 0). These are the same values as the "raw" data below - just "cleaned". The values show a very good correlation to the arrival time  of the XUV pulses in the experiment (see help).
1084 -units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
1085 -
1086 -\\
1087 -
1088 -(% style="color: rgb(255,102,0);" %)DBC2/electron bunch arrival time (raw)  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1032 +(% style="color: rgb(255,102,0);" %)DBC2/electron bunch arrival time{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1089 1089  //always saved (PBD)//
1090 -{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE{{/code}}
1091 -(% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE {{code language="none"}}DAQ channel: {{/code}}(%%)
1092 -desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2). Here the complete bunch train from the FEL is recorded (FLASH1 and FLASH2 pulses). Thus there are values from FLASH 2 in the second part. they may be separated by several "0" values if the reprate is different from 1 MHz ...  - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help). 
1034 +DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE
1035 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.ABSOLUTE(%%)
1036 +desc: Electron bunch arrival time measured with the BAM inside the accelerator (after bunch compressor 2) - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help).  typically used for FLASH2
1093 1093  units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
1094 1094  
1095 1095  \\
1096 1096  
1097 -(% style="color: rgb(255,102,0);" %)DBC2/error (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1041 +(% style="color: rgb(255,102,0);" %)DBC2/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1098 1098  //always saved (PBD)//
1099 -(% style="color: rgb(0,0,0);" %)E.bamError{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM{{/code}}(%%)
1100 -(% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMERROR{{code language="none"}}DAQ channel: {{/code}}(%%)
1043 +DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E.bamError(%%)
1044 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMERROR(%%)
1101 1101  desc: If the value is 0 , the BAM is working well. If it is non-zero there is a problem !!
1102 1102  
1103 1103  \\
1104 1104  
1105 -(% style="color: rgb(255,102,0);" %)DBC2/status  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1049 +(% style="color: rgb(255,102,0);" %)DBC2/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1106 1106  //always saved (PBD)//
1107 -(% style="color: rgb(0,0,0);" %)E..bamStatus.//2//{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM{{/code}}(%%)
1108 -(% style="color: rgb(0,0,0);" %): FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMSTATUS.2{{code language="none"}}DAQ channel{{/code}}(%%)
1051 +DOOCS prop : FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E..bamStatus.//2//(%%)
1052 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/FL0.DBC2/ARRIVAL_TIME.BAMSTATUS(%%)
1109 1109  desc: status bit: 0 - data is valid; 1 - beam present; 2 - calibration ongoing; 3 - feedback enabled; 4 - feedback acting;  mostly check for bit 0 == 1 is sufficient
1110 1110  
1111 1111  \\
1112 1112  
1113 -====== **BAM FL2.SEED5**{{code language="none"}}{{/code}} ======
1114 -
1115 -/FL2/Electron Diagnostic/BAM/**SEED5**(% style="color: rgb(255,102,0);" %)/electron bunch arrival time  (HDF5 name not yet implemented - see zraw)
1116 -
1117 -//always saved (PBD)//
1118 -(% style="color: rgb(23,43,77);" %)**FL2.SEED5**(%%)
1119 -(% style="color: rgb(0,0,0);" %)channel: FLASH.SDIAG/BAM/(% style="color: rgb(0, 0, 0); color: rgb(23, 43, 77)" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)/ARRIVAL_TIME.ABSOLUTE.SA1.COMP
1120 -{{code language="none"}} DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIME.ABSOLUTE.SA1.COMPDAQ {{/code}}(%%)desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020.. The property contains only the arrival time of the bunches sent to FL2 (e.g. if there are 30 bunches in FL2 the first 30 values are the arrival time the remaining numbers should be only 0). These are the same values as the "raw" data below - just "cleaned". The values show a very good correlation to the arrival time  of the XUV pulses in the experiment (see help).
1121 -units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
1122 -
1123 -\\
1124 -
1125 -\\
1126 -
1127 -(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/electron bunch arrival time (raw) (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1057 +(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/electron bunch arrival time{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1128 1128  //always saved (PBD)//
1129 -(% style="color: rgb(23,43,77);" %)**FL2.SEED5**{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIME.ABSOLUTE{{/code}}(%%)
1130 -**~ **(% style="color: rgb(0,0,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(0, 0, 0); color: rgb(23, 43, 77)" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)/ARRIVAL_TIME.ABSOLUTE {{code language="none"}}DAQ channel:{{/code}}(%%)
1131 -desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020. Here the complete bunch train from the FEL is recorded (FLASH1 and FLASH2 pulses). Thus there are values from FLASH 2 in the second part. they may be separated by several "0" values if the reprate is different from 1 MHz ...  - It shows a very good correlation to the arrival time  of the XUV pulses in the experiment (see help). 
1059 +DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL2.SEED5(%%)/ARRIVAL_TIME.ABSOLUTE
1060 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL2.SEED5(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.ABSOLUTE(%%)
1061 +desc: Electron bunch arrival time measured  with the BAM  before the undulator (pulse resolved data). This one was newly installed in 2020.  
1132 1132  units: fs (bigger numbers (typically) indicate later arrival times of the electrons).
1133 1133  
1134 1134  \\
1135 1135  
1136 -(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/error (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1066 +(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1137 1137  //always saved (PBD)//
1138 -(% style="color: rgb(23,43,77);" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)E.bamError{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIM{{/code}}(%%)
1139 -(% style="color: rgb(0,0,0);" %): FLASH.SDIAG/BAM/(% style="color: rgb(0, 0, 0); color: rgb(23, 43, 77)" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)/ARRIVAL_TIME.BAMERROR{{code language="none"}}DAQ channel{{/code}}(%%)
1068 +DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL2.SEED5(%%)/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E.bamError(%%)
1069 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL2.SEED5(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.BAMERROR(%%)
1140 1140  desc: If the value is 0 , the BAM is working well. If it is non-zero there is a problem !!
1141 1141  
1142 1142  \\
1143 1143  
1144 -(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/status  (HDF5 name not yet implemented - see zraw){{code language="none"}}/FL2/Electron Diagnostic/BAM/{{/code}}(%%)
1074 +(% style="color: rgb(23,43,77);" %)SEED5(% style="color: rgb(255,102,0);" %)/error{{code language="none"}}/FL1/Electron Diagnostic/BAM/{{/code}}(%%)
1145 1145  //always saved (PBD)//
1146 -(% style="color: rgb(23,43,77);" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)E.bamStatus.//2//{{code language="none"}}DOOCS prop : FLASH.SDIAG/BAM//ARRIVAL_TIM{{/code}}(%%)
1147 -(% style="color: rgb(0,0,0);" %)el: FLASH.SDIAG/BAM/(% style="color: rgb(0, 0, 0); color: rgb(23, 43, 77)" %)**FL2.SEED5**(% style="color: rgb(0,0,0);" %)/ARRIVAL_TIME.BAMSTATUS.2{{code language="none"}}DAQ chann{{/code}}(%%)
1076 +DOOCS prop : FLASH.SDIAG/BAM/(% style="color: rgb(23,43,77);" %)FL2.SEED5(%%)/ARRIVAL_TIM(% style="color: rgb(0,0,0);" %)E..bamStatus.//2//(%%)
1077 +DAQ channel: (% style="color: rgb(255,102,0);" %)FLASH.SDIAG/BAM/(% style="color: rgb(255, 102, 0); color: rgb(23, 43, 77)" %)FL2.SEED5(% style="color: rgb(255,102,0);" %)/ARRIVAL_TIME.BAMSTATUS(%%)
1148 1148  desc: status bit: 0 - data is valid; 1 - beam present; 2 - calibration ongoing; 3 - feedback enabled; 4 - feedback acting;  mostly check for bit 0 == 1 is sufficient
1149 1149  
1150 1150  \\
1151 1151  
1082 +\\
1083 +
1152 1152  [[Contents>>doc:||anchor="Contents"]]
1153 1153  
1154 1154  \\